Jump to content
SAU Community

DIY R32 cooler install

JH32

By JH32,
in Engines & Forced Induction

 Share

Recommended Posts

JH32 Grand Master

JH32

Posted
Posted

This is for anyone who has an R32 and is thinking of paying someone to fit their cooler.

After getting quotes of around $650 to fit my intercooler, I decided that the money was better spent on beer, so my brother and I went to work fitting the thing :)

It was actually surprisingly easy, and let me be the first to admit that my mechanical skills aren't that flash. I pulled the front bar off, removed all the stock cooler components including supports, pipes etc but left the pipes that are in the engine bay.

I then had to cut a few parts of the metal supports to fit the cooler and piping in, but nothing major. Luckily for me, it appears that my car probably had a front mount in Japan so the big hole in the support bar at the front had already been done.

I then drilled 2 holes in the support bar and bolted the cooler to that. The piping then went out of the cooler on the drivers side and back underneath, running along the length of the front of the car to meet up with the stock piping.

It took about a day in total but now my car feels HEAPS better!! I'm going to put it on the dyno and get the timing and boost set properly and then take it to the drags :(

Anyway I thought I'd write this in case other people were going to be lazy and get someone to fit their cooler for them! Don't be lazy fit it yourself it's not that hard!! Instead of paying $650 it cost me about $180 for all the parts.

You've also gotta have a few brews to hand when undertaking such an operation :) :alcoholic

;)

oh here's a pic of how we did it

409james_bar.JPG

Link to comment
https://www.sau.com.au/forums/topic/23142-diy-r32-cooler-install/
Share on other sites
MM2death Grand Master

MM2death

Posted
Posted

JiMiH, i am almost ready to do my own FMIC installation.....my 600x300x76 Hybrid is sitting in my room......anyhow, was it easy to route the piping back to the standard pipes? Will that 180 bend on the drivers side affect velocity? What material did you use for the piping.... I think i'm going to use grade 304 stainless. What size is your cooler?

Your install job looks neato btw...

Regards,

Scott

JH32 Grand Master

JH32

Posted
  • Author
Posted

Scott,

it was pretty easy to route the piping back to the original pipes. You've just gotta be careful with your measuring. For the 180deg bend I bought a donut and then cut it in half. This way you get the tightest bend. I had to angle it downwards so it would fit behind the cooler, and in front of the radiator. It also has to go slightly below that fan on front of the radiator. I'm not sure what effect the 180deg bend has, but it doesn't seem to be any laggier than stock so I assume it hasn't had any negative effects :D

My cooler is exactly the same as yours, just not branded a Hybrid. Same dimensions etc also.

The bits I bought were :

1 x 2.5" donut

2 x 90deg 2.5" mandrel bends

2 x 3" ---> 2.5" pipe reducer

2m of 2.5" piping

yeah I mounted mine to the bar above the cooler ... not sure if it's strong enough but the piping holds it, and the whole things as tight as a nun's snatch :P but i'm also get some brackets welded to the underside soon to give it some extra strength.

Hope that helps some :)

Mr R32 M-Spec Experienced

Mr R32 M-Spec

Posted
Posted

I was in the same boat, even though I had purchased the HKS Kit for the R32 GTST, I have no technical skills at all. got a mate who knows what he is doing and we knocked it over on a saturday arvo. cut 1 hole and it looks sweet as. HKS kit fits with no modification bar that 1 hole we had to cut, although I should mention there was already a dotted line in the chasie where a pipe should go... guess the GTR's and GTS's share a few similarities

didn't have to cut the support bar or bumper though, fit straight on. cost me $1300.00 delivered to me. we cut out the front bumper and put mesh in it though, for more of a sporty look :D:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Jarsky
      After market rear camber arm adjustment

      By Jarsky · Posted

      This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Its a well known brand in New Zealand; its a rebrand of the Rhino RAV3.  I don't know what the wiring difference *is* between the rev.1 (installed about 15 years ago) and rev.2; but as you say I would think its reasonable that it uses the same immobiliser relay circuits. I had a look but couldnt see a similar harness; but didnt move things around since I didnt want to mess with it   It was one of AVS well known Authorised Installers; I spoke to AVS themselves about it but theyre unsure hence seeking advice more so from the skyline community who are more familiar with the actual car and its wiring. Im in Auckland; but the installer is on the other side of the city so hes very reluctant to come back to even look at it to confirm something isnt connected into the wrong wire.  I dont want to drop the name since they *did* do a really good job for the most part. Everything is very tidy and he fully replaced all the alarm wiring, all the sensors, the wiring to the door motors, installed a switch which was never installed in the first place...really happy with the alarm install itself..just not this one issue. We all make mistakes, if it is the alarm, I just want my fuel pump getting proper switched, fused, power as it was; without having to shell out for an auto electrician to switch a wire and tell me it was the alarm. 
    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
×
×
  • Create New...