Jump to content
SAU Community

Recommended Posts

I've recently bought a 32 and have sometimes noticed a whiff of petrol when parked and sometimes when driving. I had a look around in the engine bay and noticed it was a bit damp and dirty around a few of the injectors. I've done a search and found it seems to be common occurance with rb20s.

My question is, is it something dangerous that needs fixing asap? Could I go through a drift/track day with it?

Any help would be appreciated

Cheers

Link to comment
https://www.sau.com.au/forums/topic/231436-leaky-injectors/
Share on other sites

think about it like this, you have fuel leaking out of a pressurised source into a hot engine bay.

so a highly flameable material next to a whole heap of heat, and if it leaks a lil more and has a bit of a spray instead, and it gets on the exhaust then yeah, big trouble

if you have a car problem related to one of these

FUEL

BRAKES

SUSPENTION

then get it fixed immeditatly

Link to comment
https://www.sau.com.au/forums/topic/231436-leaky-injectors/#findComment-4064543
Share on other sites

Time for some GTR injectors
No it's not. That would entail a re-tune to compensate for the higher amounts of fuel that would be delivered on each opening of the injector.

Get the injectors looked at. They may be repairable. If not, then replace them with RB20 injectors.

Link to comment
https://www.sau.com.au/forums/topic/231436-leaky-injectors/#findComment-4065412
Share on other sites

Very common.

Clean the effected area to locate the exact spot of the leak. Its most likely from

- the o-ring up top

- upper insulator

- lower insulator

- the injector body itself (the plastic part where theres an indent from the injection molding

Nissan OEM seal/insulator are about $80'ish I think, though theres a link on SAU from a guy who sells them for dollars.

Iv never done it, though guess you could pressurize the FPR to simulate having some boost / load under it; proper rail pressure would assist in locating leak.

Link to comment
https://www.sau.com.au/forums/topic/231436-leaky-injectors/#findComment-4067376
Share on other sites

I had an issue in my 180sx as well, was a pinched 0-ring, took the injectors out, replaced all the 0-rings and had the injectors ultrasonically cleaned while out of the car.

Turns out, my injectors where so far gone that 3 of the 4 where stock open to some degree, and the 4th was spraying all over the place. Cleaned the injectors, re-fitted them with new o-rings.

The difference was amazing, and something else that I found was the injectors being stuck open mean that fuel was leaking into the cylinder when the engine was shut off, and if left overnight would eventually soak down into the sump and foul the oil as well, so I had seriously thin oil, and fuel leaking outside of the engine.

Also, as Adam said, any track that is worth bothering about will spot the leaking injector patch and immediately turn the car around as a risk.

Thanks,

B.

Link to comment
https://www.sau.com.au/forums/topic/231436-leaky-injectors/#findComment-4068686
Share on other sites

Also going to check out my O2 sensor as my fuel economy is rubbish!

You have confirmed you have leaking injectors, and then you say you have poor fuel econemy, I am going to sound a little smart-arse here, but I would put some of that poor fuel econemy to the fuelt hat is leaking out of the engine block and vanishing down the side of the block, instead of into the cylinders for combustion.

Make sense?

B.

Link to comment
https://www.sau.com.au/forums/topic/231436-leaky-injectors/#findComment-4069239
Share on other sites

On the way home from work I gave the car a quick squirt down my road and I heard the injector start ticking. Popped the bonnet and there was a shitload of fuel around #3 injector. Almost dripping out.

I've stopped driving the car untill I get it fixed now :worship:

Link to comment
https://www.sau.com.au/forums/topic/231436-leaky-injectors/#findComment-4073392
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...