Jump to content
SAU Community

Optimum Tyre Specs For R34 Gtr Rims ?

godspeed
 Share

Recommended Posts

godspeed Apprentice

godspeed

Posted
Posted

g'day.

Im looking at getting Bridgestone Adrenaline RE001s to fit on my R34 GTR rims (fitted on my R32 GTR).

What size do you guys recommend for these rims? Is it better to go more narrow for the fronts or keep them all the same widths?.

R34 gtr rims are 18" x 9".

The car will be predominately street use with the occassional track day.

Link to comment
https://www.sau.com.au/forums/topic/231856-optimum-tyre-specs-for-r34-gtr-rims/
Share on other sites
Duncan1 Rising Star

Duncan1

Posted
Posted
g'day.

Im looking at getting Bridgestone Adrenaline RE001s to fit on my R34 GTR rims (fitted on my R32 GTR).

What size do you guys recommend for these rims? Is it better to go more narrow for the fronts or keep them all the same widths?.

R34 gtr rims are 18" x 9".

The car will be predominately street use with the occassional track day.

Hey mate, I had the same rims on the same car, i put on bridgstone potenza SO-3's. they were 255/35/18's. they were a very very good tyre and didnt scrub at all.. hope this helps..

godspeed Apprentice

godspeed

Posted
  • Author
Posted

Thanks guys for your replies. I think i will take heed on the 255/35/18 on all corners. I am now looking at importing some Bridgestone RE-01R's from Tirerack.com. I heard they are pretty damn sticky and are a good compromise for street and a little bit of track work. Used to have Yoko Advans but didn't rate them much. If i cant get my hands on the RE-01rs, i may consider Federal 595 RS-R or Toyo T1-Rs. Its all too confusing, too many options and opinions out there. :wave:

Ronin 09 Grand Master

Ronin 09

Posted
Posted
Those rims came standard with 245's... which fit well... 255's will fit ok too, touch more baggy.

i have 255 michelins on my 34s and they're actually slightly stretched.

given that manufacturers widths vary between brands, a 245 or 255 road would be fine.

I've seen some 265 road tyre fitments on 34 wheels where the sidewalls are straight up - not baggy

donkey Community Regular

donkey

Posted
Posted (edited)

hey godspeed,

i had 285 SO3 bridgestones on my r33GTR, they fit sweet, looked like a beast ha, but tram lined quite badly, went down to 255 toyo's, fixed problem

Edited by donkey
Beer Baron Grand Master

Beer Baron

Posted
Posted

245s are the way to go on 9inch wide rims in my opinion. depends on the tyre of course too. I've tried 235, 245 and 255 on 9 inch wide rims. all are ok (though the 235s have always been semi slicks which are about the same width as a 255 road tyre).

so to recap, go for the 245s all round. either 40 or 45 profile.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

×
×
  • Create New...