Jump to content
SAU Community

R32 Diff Question

mark32gts-t
 Share

Recommended Posts

mark32gts-t Collaborator

mark32gts-t

Posted
Posted

My diff whines like hell and am considering just replacing the whole housing with a 2nd hand one. My question is this, my car has ABS and from what I understand it has an ABS sensor in it. Can this sensor be transferred across into a non ABS housing. I had a look on fast and there appears to be an illustration showing the sensor. Just not sure if the ABS section can be fitted into a non-abs diff housing. Included the fast image. Any help would be much appreciated. Cheers

LSD.jpg

Link to comment
https://www.sau.com.au/forums/topic/231873-r32-diff-question/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

First off, do you have oil in the diff? Do you have enough oil in the diff? Do you have new oil in the diff?

Pretty sure the ABS sensors are on the output shafts of the diff. So all you need to do is transfer those from your current diff to the replacement diff.

mark32gts-t Collaborator

mark32gts-t

Posted
  • Author
Posted
First off, do you have oil in the diff? Do you have enough oil in the diff? Do you have new oil in the diff?

Pretty sure the ABS sensors are on the output shafts of the diff. So all you need to do is transfer those from your current diff to the replacement diff.

yes, diff oil has been replaced and is filled to the correct level. it only whines on deceleration, from what i've read its the meshing of the gears that have "play" due to wear and this is what whines... anyone else???

bubba Grand Master

bubba

Posted
Posted
Pretty sure the ABS sensors are on the output shafts of the diff. So all you need to do is transfer those from your current diff to the replacement diff.

Yes that is where the ABS sensors are, my Nismo diff came with new output shafts/flanges and they had the ABS sensors on them (my car doesn't have ABS).

mark32gts-t Collaborator

mark32gts-t

Posted
  • Author
Posted

Just thought I'd upload some pics of where the ABS sensor is located, for reference sake. Its on the tailshaft input and not on the driveshaft outputs. The sensor bolts into the actual housing so unless the non-abs diff has the hole blocked off I dont think its as easy as just swapping the sensor over. Thanks to the people who responded anyways. pics:

ABSSemsor1.jpg

ABSSensor.jpg

mark32gts-t Collaborator

mark32gts-t

Posted
  • Author
Posted

I think it would be possible to swap the internals over. But I dont really have time to be doing it right now.If I have to swap stuff over I may as well do what 'White GTS-T' said and buy a two way

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...