Jump to content
SAU Community

CRD Dyno day - DATE CHANGED - Now Oct 12th 2003


Recommended Posts

  • Replies 240
  • Created
  • Last Reply

Top Posters In This Topic

People - We have a BBQ available to us for tommorrows Dyno Day so please bring all nessesary food and drink. This strictly BYO, no food/condiments etc will be provided

See all of you in the morning

Nick

Another things guys I have spoken to ASM (Auto Salon Magazine) who are interested in doing a story on the Dyno Day.

They are unable to attend unfortuantely but have asked that we get some nice hi res photos of the event.

We are therefore looking for volunteers who can take photos and email them through to me for submission to ASM.

If anyone out there can assist please let me know tommorrow

Cheers

Nick

A good morning, sorry i had to head off so early.

thought i would have made a bit more power than i did :(

good to meet some of the boys and i'll meet the rest of you next time, might possibly be coming to the big cruise next fridy.

big thanks to nick for organising.

:)

B-Man, unsure *shrugs*

I had a Bosch 040 fitted about a month ago and the car is deffinetly quicker than it was when i did the 203 at Unigroup. I don't believe that CRD ran in Shootout mode (doesn't say on bottom of the printout) so add around 8-10% to adjust for that.

Still happy though coz im only using the standard ECU and no other management :(




  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...