Jump to content
SAU Community

Recommended Posts

to day i ran my 33 gtst down the 1/4 after a couple of passes at 12.2@123mph with a crap 60 foot of 2.2, i ran my best 60 foot at a 1.8 but right after i hit second gear a all mighty bang went off (back fire) and the car lost power for a split second so i came off the gas until 3/4 track and jump on it again and it felt fine ,i got back to the pit area and i noticed on when you lightly press the gas it runs like its missing ,i also noticed this in the last three runs leading up to my last run ,now i think its ???????? but what i would like is some input from some sau members on what they think it could be......thanks.

Link to comment
https://www.sau.com.au/forums/topic/232530-what-do-you-think-it-could-be/
Share on other sites

could be anything

sounds like plugs need changing most likely.

yes ill give that a go today!!

pm-r33 im making 304kw atw but i think there is a little more to come as im running 17.5 psi

Edited by WARLORD

i had this problem with my car, it turned out to be the intercooler pipe

one of the vacuum lines came off the fuel pressure reg and for some reason (im not gonna pretend i know what im talking about here) it backfired and pretty much just died in the arse, it would idle but wouldnt accelerate, check your cooler piping, find the loose hose and reconnect it

ps. this was a right pain in the arse to diagnose and fix at 2am on scarb beach rd in the rain :P *shakes fist in a menacing fashion*

intercooler all good .

what i have noticed is that when the car is cold its fine andwhen its hot it plays up.

could be coil packs.i dont think its normal to happen so low in the rev range but i guess anything can happen ,there only 3 years old ,ill have to check them

has anyone got any more ideas

intercooler all good .

what i have noticed is that when the car is cold its fine andwhen its hot it plays up.

could be coil packs.i dont think its normal to happen so low in the rev range but i guess anything can happen ,there only 3 years old ,ill have to check them

has anyone got any more ideas

did you check the inside of the 90 deg bends the run through in in left inner gaurd

,

earth wire .....i noticed the earth wire on the turbo side is not there. does anyone have pics to what it is connected to cos ive got the earth wire i know one side is on the exhaust manifold but have no idea what it plugs into.

o and could this be part of my problem. :D

hey warlord

try pumping compressed air into your intake system with a compressor.

i do this about every 6 months as it shows up any leaks in the system.

the easiest way i have found is undoing the clamp where your afm is, getting a plastic freezer

bag putting over the afm and then reinstalling the afm and doing the clamp up.

you can then use a trigger nozzle from your air comp stick into the fuel reg hose and pump 2 bar

into your intake system.

a lot of leeks wont show up unless there under pressure so this is the quickest and easiest way that i have found

and works every time.

and also a poor earth wont do the engine any good put it that way.

hey warlord

try pumping compressed air into your intake system with a compressor.

i do this about every 6 months as it shows up any leaks in the system.

the easiest way i have found is undoing the clamp where your afm is, getting a plastic freezer

bag putting over the afm and then reinstalling the afm and doing the clamp up.

you can then use a trigger nozzle from your air comp stick into the fuel reg hose and pump 2 bar

into your intake system.

a lot of leeks wont show up unless there under pressure so this is the quickest and easiest way that i have found

and works every time.

and also a poor earth wont do the engine any good put it that way.

thanks !!!!!

what do you recommend i use for a earth cable, and the best place to put it.

Yeah i do. Hope i can explain this well.

Behind the power steering resevoir, on the strut tower down near the turbo intake, there should be a little gold piece of metal, the black connector just slides over that.

Yeah i do. Hope i can explain this well.

Behind the power steering resevoir, on the strut tower down near the turbo intake, there should be a little gold piece of metal, the black connector just slides over that.

that has got to be one of the best descriptions i have ever read,,,i new where to go and found it it 2 sec thanks.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...