Jump to content
SAU Community

Black Paint With Candy Red Metal Flakes On R32

Rocky88

By Rocky88,
in Exterior & Interior Styling

 Share

Recommended Posts

Rocky88 Proficient

Rocky88

Posted
Posted

I'm getting my black R32 resprayed sometime in near future and I want something more exciting yet still black so I'm considering to respray it in black with candy red metal flakes. I've got idea from Juiced: HIN (computer game for those of you that don't know it). This is how it looks in game:

redflakehc6.jpg

redflake2jo4.jpg

This is basically how I want my car to look... black with red metal flakes, probably something like this: http://cgi.ebay.com.au/CANDY-RED-METAL-FLA...1742.m153.l1262

Does anyone have experience with such paint? How would that turn out in real life (cant rely on computer game, lol).

Bainator Enthusiast

Bainator

Posted
Posted

I painted the bonnet, and some other details on my old nissan patrol with silverflakes.

It requires some work...

1. spray the clear-coat with flakes, let it dry.

2. go over the painted area with fine sandpaper and wet sand it. Do good work here, and make sure its smooth.

3. spray again with clear-coat (no flakes)

4. If the result is good now you are finish with the paitning, and can start polish the car. If its not good repeat step 2&3.

If you use a poor flake-fabric the flakes can either sink or float in the clear-coat, and you will get an uneven layer of flakes. Test the flakes, and trye spray something just to test it (like an old patrol) :D

Tried to upload pics, it failed. So i used a norwegian pic uploader site:

242116.jpeg

242117.jpeg

Craved Grand Master

Craved

Posted
Posted

IMG_0138small.jpg

Paint with pearl red flakes over black base --- i used WAY too much red flake in the clear - tone it back and it should work like you think - but it will always look a little red

Triptych Proficient

Triptych

Posted
Posted (edited)

Actually I have seen a car that looks similar in paint to the game photos you posted at a hod rod show years ago which made me want a paint job the same. Here is that car

dscn1022lj0.th.jpg

Edited by Triptych
Rekin Grand Master

Rekin

Posted
Posted
IMG_0138small.jpg

Paint with pearl red flakes over black base --- i used WAY too much red flake in the clear - tone it back and it should work like you think - but it will always look a little red

nice, how much would that cost to do?

Craved Grand Master

Craved

Posted
Posted
Actually I have seen a car that looks similar in paint to the game photos you posted at a hod rod show years ago which made me want a paint job the same. Here is that car

dscn1022lj0.th.jpg

that is realllyyyy nice

maybe find out the builders name - they will advertise which paint they used - maybe not colour but brand atleast.

Rocky88 Proficient

Rocky88

Posted
  • Author
Posted
Actually I have seen a car that looks similar in paint to the game photos you posted at a hod rod show years ago which made me want a paint job the same. Here is that car

dscn1022lj0.th.jpg

That looks sweeeeet.  :P (we really need a :drool: smiley).  Cheers guys.

I'm planning to get my R32 resprayed later this year or as soon as I repay my credit card and then I'll share results with you. :(

Dahtone Racing Grand Master

Dahtone Racing

Posted
Posted

that colour on the hot rod is House of Kolor Kandy Brandy Wine, not sure what base they have used though

by the looks of the pics in the first post you want a cherry black colour

kandy cherry black will look awesome and be exactly what you're after

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • GTSBoy
      R34 25GT Engine Light 21

      By GTSBoy · Posted

      Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...