Jump to content
SAU Community

Recommended Posts

http://www.motorauthority.com/news/videos/...ailer-released/

Paul Walker and Vin Diesel return for the fourth instalment of the Fast & Furious series and once again play characters caught up in the seamy underworld of truck hijacking and stolen cars. The first official trailer for the upcoming movie has just been released, revealing that a number of other characters from the first movie also return. We also get a look at some of the new of the film, including a Subaru WRX STI, a Chevrolet Nova SS, a couple of Nissan Skylines and even a Buick Grand National. The movie is set to open next summer but in the meantime follow the jump to catch the new trailer.

nice, actually looks like it could be good! Dare I hope for a PROPER sequel to the first Fast and Furious?

Nice to see a couple of R34s in the mix too, I also managed to spot a Ford RS200! The Subie STi wasn't too over the top and that Buick GNX at the start is beautiful too. Is it possible that the car people on an FnF movie have discovered a modicum of taste?

Everyone slags off FnF films, but really, why do you watch them? To be entertained. If i watch a film, and walk away entertained then the movie's done its job. Some entertain with engaging storylines, others with cars explosions and tits. FnF falls in the latter category, but you still wind up being entertained.

FnF4 will be more of the same entertaining explosions and tits.

Everyone slags off FnF films, but really, why do you watch them? To be entertained. If i watch a film, and walk away entertained then the movie's done its job. Some entertain with engaging storylines, others with cars explosions and tits. FnF falls in the latter category, but you still wind up being entertained.

FnF4 will be more of the same entertaining explosions and tits.

Well said. Now bring on the explosions! and tits!!! :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...