Jump to content
SAU Community

Dropping The Shaft

Adz2332
 Share

Recommended Posts

Adz2332 Grand Master

Adz2332

Posted
Posted

How hard is it to drop the shaft to make a GTR 33 run in RWD only?

Does anyone have a step by step?

Or pics etc?

How hard is it? Anything needed to do it?

Just looking at going to an event and it has a dyno, but only a rear wheel drive dyno...

Any help would be good thanks

Ps not sure if its the right section soz!

Link to comment
https://www.sau.com.au/forums/topic/233703-dropping-the-shaft/
Share on other sites
unique1 Mentor

unique1

Posted
Posted (edited)

it will take about 10 min max. You need 2x12mm spanners (preferably 1 of them a ring spanner as it might be tight). Also a 14mm socket or spanner to remove the clutch slave cylinder.

just jack the drivers side of the car up and unbolt the 2 14mm bolts holding the slave cylinder on, then let that hang out of the way and undo the 4 12mm nuts and bolts on the front diff end of the front shaft. Remove all 4 bolts and pull the shaft away from the front diff and the front flange will drop down and then pull the shaft towards the front of car and the gearbox end will slide out. The gearbox hole is sealed so dont bother worrying about fluid leaking out or anything. Then rebolt the clutch slave cylinder back on and away u go.

Edited by unique1
toddlls Proficient

toddlls

Posted
Posted

Go buy a white and another colour paint pen and mark the edges of the shaft with the pens so you know the exact location when re-assembly is required.

I've seen the R32 boys pull a fuse and stop the 4WD that way, sorry dont know too much about the R33's.

On my 4WD laser I was told never to do this-disconnect the shafts- by plenty of people as it can really mess things up.

Have used the paint pens when removing just about everything from hoses, vacuum lines, doors, boots & tailshafts when replacing clutches and the like and its never failed there :(

unique1 Mentor

unique1

Posted
Posted
and its just as easy to put back in???

Also i cant damage anything by doing this?

and no fluids at all will leak???

cheers mate

yes its as easy to put back in, no damage at all, no fluid will leak. I do this on my stagea (running gtr driveline) everytime i do dyno tuning and never caused an issue, i also drive around alot of the time with shaft removed and no problems.

  • 10 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      You Gregged a whole racetrack!?
    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...