Jump to content
SAU Community

Recommended Posts

Hi all, im looking at buying a digital slr, im new to photography but i want to get a decent camera that will not only be good through the beginer stage of learning but also good once i get the hang of it, i dont want to get good and have to throw it out :D

Im looking at paying around 700-1000 $$$ for one

Any advice would be great

cheers

Link to comment
https://www.sau.com.au/forums/topic/234358-digital-slr-help/
Share on other sites

yeah for that price range I would say 450D or 400D. I use the 400D myself, so don't know much about the other camers out there as I only look at the canon range when shopping around.

If you go for the 400D you can probably get a few extras with it. I wouldnt bother thinking about megapixels though. Unless you plan on shooting pictures and blowing them up to huge posters, 10mp would be more than enough.

the 400D has been great for learning and I'm no where near getting ready to upgrade the camera yet

I'm thinking of selling my canon 350d with 18-55 IS lens if you are keen.

If you are keen on what the camera can do check out my website (www.sidd-rishi.com)

Price: $500. Comes with extra battery, manual, box etc..

The 400D is discontinued.

1000D is its replacement. but some features have been lowered on the new model.

450D is a much nicer camera and you get the IS lenses as part of the twin lens kit.

either the 1000D or 450D will be a fantastic camera and no need to update for ages as SL!M said. you will upgrade your lenses before the camera.

Just my 2c (even if its a couple of days late lol)

Hope you enjoy it no matter your choice anyways

Great entry level camera.. 10 mega pixels, self sensor clean, weather proof, 11 point auto focus (WOW), etc etc..

yea comes with sigma lenses..

You have a great variety of sigma lenses to choose from.

If you on a budget just get the normal 18-55mm lens..

If you have a spare 300 more or so, get the 17-70mm sigma lens..

Either way great entry level camera :P

ps. forgot to mention it all depends on what you wanna shoot. You can get the twin lens kit with this body also. I think its the 70-300 lens also??

Best advice.. go into a shop and try it out yourself!!

Edited by siddr20

dont buy a dslr camera coz it has live view :P

Buy it coz you need it..

That is if you wanna get into marco work, astro photography work etc..

Otherwise no point having it.

The whole point of slr is too look thru the viewfinder!! heheheh

But anyways 1000d is a great entry level camera also :)

live view is not needed on a DSLR for 99% of photography. I used to think it was. when I went from a compact to a DSLR about 2 or 3 years ago I really missed live view and was pissed that I didn't have it. then after about a year with the DSLR I got a hold of one that did have live view for a while. and I hated it. live view is rubbish. it's only useful maybe to initially frame shots on a tripod on weird angles, or macro shooting etc but apart from that it's pretty useless. on a DSLR you need to be using the viewfinder. and the funny thing is now when I use one of our compacts I find I want to use the view finder too. you get much better pics. liveview is good for your camera phone, that's about it. so definitely don't buy a DSLR because it has live view, there are so many more important aspects than that.

and my preference is always with the canon cameras. they make lovely DSLR in all price ranges.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...