Jump to content
SAU Community

The car goes in today for the tune

bless_you

By bless_you,
in Western Australia

 Share

Recommended Posts

bless_you Rising Star

bless_you

Posted
  • Author
Posted

Thanks Erik,

the car is just:

cat back 90mm

k&N filter

turbosmart type2 BOV

bleed valve running 10psi

and SAFC II

still have the miss problem though, so i know what im upto this weekend. will have to sort out if its the coil packs or the ignitor module or the plugs :)

i will be at pool place this thursday night, may see you there.

Nate

MrGTST Grand Master

MrGTST

Posted
Posted

I don't think Genie's dyno is as bad as everyone says.... When Xspeed had my car and took it to Genie to dyno as part of the tune I got 285rwhp on the Genie Dyno.... At our SAU dyno day at SST my car pulled 284.4 HP.... both are very close results to each other....

GTS-t VSPEC Grand Master

GTS-t VSPEC

Posted
Posted

Brett, I agree, but the real issue is they they still have correction factors, which means if they want to see a big difference, then they can make it happen. SST and one other place has had there correction factors removed, and there dyno figure can't lie.

C yar Veteran

C yar

Posted
Posted
Originally posted by hks-s14

Change your plugs to NGK BCP6ES coppers...they rock.  Steve put these into my car when I developed a miss whilst he was tuning it, my iridiums could not handle any more than 200hp, the NGK's fired perfectly up to 260hp.

what did ya gap them to ?? 0.8mm yeah

C yar Veteran

C yar

Posted
Posted
Originally posted by hks-s14

Change your plugs to NGK BCP6ES coppers...they rock.  Steve put these into my car when I developed a miss whilst he was tuning it, my iridiums could not handle any more than 200hp, the NGK's fired perfectly up to 260hp.

what did ya gap them to ?? 0.8mm yeah

bless_you Rising Star

bless_you

Posted
  • Author
Posted

well... its believed that the miss may be caused by a AFM!

im heading down to cypher on saturday to see if i can swap one over...

i have checked the coil packs, and they all read 0.7 ohms across the pins, and plugs are fine.

so its either the AFM or the ignitor module... i dont know... its all too much!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...