Jump to content
SAU Community

Recommended Posts

United petrol stations have a performance petrol that contains ethanol but has a higher then 98 octane rating then most servo premiums.

Shell also has V-POWER racing which is 100 octane and contains 5% ethanol.

my question is is this octane petrol bad for a Non Turbo, skyline?

Link to comment
https://www.sau.com.au/forums/topic/234884-united-plus-petrol-in-a-skyline/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

well i have heard that ethanol based fuels in the long run can rust fuel lines etc thats about it thou. Also another thing i have heard that if u use a much higher octane fuel then what the car was made for u can burn the valves??

i have used united boost 98 ( with 5% ethanol) in my rb20det for the last 3 years i have owned my car and yet to have any problems with the fuel

it actually runs better than bp 98 ive noticed, bp gives it a rough idle and sorta rough drive through the rev range

however yet without a problem i will still use this in my car

this has been covered to death

using higher octane fuel is fine

without a retune you wont get any gains other than it acting as a detonation killer

you wont gain any power without a retune

ie: putting 100ron in a stock GTST will give zero, unless you tune for it

but it will take away knocking if you do get some with normal 98 on your current setup

ethanol in a std car is fine it wont do any harm or melt your fuel lines etc

ive been using shell vpower racing 100ron for about 5 months (ish) now and its fine

i havent changed a single thing, std GTR pump, std lines, std injetors etc

My car is stock and at the last RE Customs Dyno day I got close to 150kWs and I'm sure I had been using the United 98 for at least a few weeks leading up to that... ...I had a discount card that a mate had given me and the one in Springvale is right next to my office...

Since then, when I had my last service, I was back down to around 140kWs and I've been using Caltex 98... ...Moneys been a little tight with the cutback of hours at work and the cost of fuel... ...So it is shopping dockets for me at the moment...

I doubt the fuel is the only reason for the drop in power... ...but it could be a factor...

ethanol is fine

do you honestly think shell could sell it as a std available product to every day mum and dads if it melted fuel lines and caused your fuel pump to explode?

of course not, it would be the biggest law suit and class action in australia

with a tune, is there much to be gained? or are we talking like 5rwkw

From what I remember, a few years back HPI magazine had one of their cars re tuned for ethanol based fuel.

Again from what I remember, they got around 20kw gain and more torque. Does anyone else remember this?

If you get more power with a cheaper fuel, why not move to it?

Wont do anything in the short term if you only use it once or twice here and there, although in the long run it could rust fuel lines.

A mate of mine with a NA MK4 Supra has had the problem wouldn't recommend using it on a regular basis

well thats just your opinion..

it could not be souly responsible for it, there are other factors that may have obviously contributed. All i am saying is i dont believe its wise to be running this fuel consistently in a NA. Why not just run it on normal unleaded and you will have no drama's

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...