Jump to content
SAU Community

Recommended Posts

Is your rear muffler straight thru? I have two mufflers - rear one has an S bend in it to help keep down noise, but have set it up so I can take off the rear one at track for less back pressure. If both are straight thru, prolly not much power advantage removing either, (but will sound heaps good) - that is if mid one is like a hot dog, apparently, if it's really big, turbulence may be removed if you take if off and there will be more power there.

yer the rear is a straight thru, i went and got a quote today on how much it would cost to replace it with a 3'' pipe and was 100 bucks, so ill most likely go thru with it, so when i take it off Zman ill let u know, not sure how much it would be for u to install it on to an existing exhaust, probs round the same as for me replacing it with a pipe...

cheers...ben.

my old system used to have a center muffler and a rear muffler, first i took of the center one cause it wasnt loud enough, that made a difference, but not enough for passangers to even notice it...

finnally i pulled of the rear muffler and replaced it with a smalish 3 inch cannon muffler, with very little baffling material (whatever its called).

Its definatly alot louder, but the problem with skylines (moreso ones with stock turbos), is that they are impossible to make loud, i got the dude at the exhaust shop to start it up with the system off and it still wasn't all that loud...

improvment in power is very minimal, maby a couple of kws?, but more than likely, you wont notice it.

I got mine done aswell, and it cost me $40 as well...$100 is a complete rip off!!!

Mine sounds sweet, a little droney between 2200rpm and about 2500 rpm, but nothing I can't deal with!

The RB series engines sound great, so in my books the louder the better. Sounds gold on full noise whilst drifting with the BOV going off all over the place.

I had the same dilemma a while ago - I had a 3" dump, 3" cat, and two straight-through 3" mufflers. I had a shop remove my centre muffler and replace it with a flaged piece of 3" pipe. Also had them make a dropped pipe, which comes out under the passenger seat and eliminates the cat too, for drags etc.

Anyway, after removing the centre muffler, my car was certainly louder and had a deeper note, but doesn't drone and has quite a nice note. With the dropped pipe on, it's not "that" loud at idle, but you can hear the turbo spool from about 1200rpm, and it sounds like a Nascar when the revs build up around 5k :P But yeah, whether it's too loud or not will depend on the muffling qualities of your remaining muffler. Mine seems to have been perfect, yours might make it too loud or too quiet. Just try it and see. Don't expect a massive power difference though.

  • 1 month later...

Interesting... I too have the 2 mufflers. My exhaust consists of:

3" Custom front/dump pipe -> 3" Cat -> 3" Nismo exhaust with a middle and rear muffler -> 4" Nismo Tip.

I'm thinking of getting this middle muffler cut out and replaced with just a 3" straight through pipe (or possibly getting it done so that i can swap between a muffler or straight through pipe, daily driving vs track/drag).

So about $40 and 30mins and it should be done eh?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...