Jump to content
SAU Community

Recommended Posts

ive had the baddest luck this week..

some bloody stupid cat decided to go drifting on my car causing scratches to the rear driver side quarter & roof.

now there is tiny spots of tree sap all over the car.

how do i remove tree sap from the windows & body without damaging the paintwork?

ive readup for the windows to use nail polish or metho but not for the body as it will ruin the paint.

any ideas?

cheers

Link to comment
https://www.sau.com.au/forums/topic/236637-how-to-remove-tree-sap/
Share on other sites

  dori32 said:
ive had the baddest luck this week..

some bloody stupid cat decided to go drifting on my car causing scratches to the rear driver side quarter & roof.

now there is tiny spots of tree sap all over the car.

how do i remove tree sap from the windows & body without damaging the paintwork?

ive readup for the windows to use nail polish or metho but not for the body as it will ruin the paint.

any ideas?

cheers

Hi.

The best system is hot water( not boiling but hot)mixed with some detergent- melts the sap and the detergent cleans it off.

^ ill try the hot water & detergent method this weekend.

gonna try get rid of the damn claw marks too!

using scratch X & give it a good wax/buff.

let you know how it goes.

cheers guys

Edited by dori32

i also used hot soapy water to get tree sap off. works great. comes off really easy too. its better if you can sit the car in the sun for a little while first, to let the panels warm up.

and ppl were telling me to use alcohol and shit on my paint. pffft :)

  dori32 said:
^ ill try the hot water & detergent method this weekend.

gonna try get rid of the damn claw marks too!

using scratch X & give it a good wax/buff.

let you know how it goes.

cheers guys

Before you get the claw marks off, do you want a loan of

i) DNA Test Kit and then

ii) a Shotgun?

  Terry_GT-R34 said:
Before you get the claw marks off, do you want a loan of

i) DNA Test Kit and then

ii) a Shotgun?

ii) shotgun preferbly :)

  GTS4WD said:
Bug and tar remover..

would this be okay to use on paint/bodywork ?

  dori32 said:
ive had the baddest luck this week..

some bloody stupid cat decided to go drifting on my car causing scratches to the rear driver side quarter & roof.

now there is tiny spots of tree sap all over the car.

how do i remove tree sap from the windows & body without damaging the paintwork?

ive readup for the windows to use nail polish or metho but not for the body as it will ruin the paint.

any ideas?

cheers

sorry if it's been said, i only looked at the op, had the same problem. fairly hot soapy water, & a decent scrub with a sponge helps take it away bit by bit. polished after wards on the panels & just persisted with the windows. it's quite annoying haha.

  • 3 months later...

I got some tree sap over my bonnet on Christmas Day.

Not good. The detergent just spread it around and it remained sticky.

Some obscure info came up on Google about using lard!

So after 3 minutes of using bacon fat, the SAP simply DISSOLVED !!!! Brilliant !!!!

Detergent just took the rest of that mixture away.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...