Jump to content
SAU Community

Recommended Posts

Hey guys,

I have recently bought a GTSt that has just had an engine transplant.

It was done by the guy before me (some asian guy) who got it done professionally but doent know jack bout cars.

So he knocked $2k off the price for me cos is was missing under load and i bought it.

here's the description:

Turn car on and go to accelerate after letting clutch out then it either accelerates normally (sometimes) or it will shudder and refuse to accelerate. It will then missfire and knock adversely until eventually the boost cleans up and she takes off.

If i am cruising i will have to slow down, then boost, then slow down, then boost because the engine isnt able to hold a constant rev around 2500 without beginning to shudder or surge again.

If i cruise at 120km/hr in 4th gear she is fine! lol (but my fuel bill isnt)

So to fix the problem so far i have:

-replaced the coils

-fixed one air leak where the boost gauge hose comes out of inlet manifold (there was no hose just a pipe lol)

-checked for other leaks havnt found any but im sure there must be another one somewhere!

-tested fuel pressure, it's ok

-found that my 02 sensor isnt working but i figured it isnt causing too much issue (will get it replaced)

I have found that my AFM has C33 written on it, C33 must mean C33 laurel which is funny. I have cleaned it out but it is bothering me so i will replace that.

Any other suggestions?

Link to comment
https://www.sau.com.au/forums/topic/236835-rb20det-missing-problem/
Share on other sites

today i:

-changed ignitor no result

-tried taking off and putting on different coils to exclude troublesome cylinder/s

-reset ecu

-slapped a different AFM in and it seemed to fix the problem!

i drove for about 15mins no problem although after a quick cane once i got out on to the open road (only 150kmhr) it seemed to resort back to it's old ways again!

oh and still idles like crap although i was hoping new plugs would fix that

any suggestions???

i think u should take a look along the lines of computer. if it drives fine at times then it i doubt it would be coils or anything like that as it would do it all the time.

my rb is currently doing the same thing but proly slightly different reasons. but when u said the 4th gear thing it sounds to similar.

PM for more info

P.S this forum does not condone speeding we know think u are a dickhole u should follow the road rules at all times

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...