Jump to content
SAU Community

Recommended Posts

Hey guys i dont know if this is the correct section, but im building up a track gtr and planning on circuit work on semi slicks and drifting as well with another engine setup and rwd, the motor is pretty serious (over 550rwhp) so i need a fair bit of fuel. I am gonna go straight for a fuel cell instead of using the original tank setup. I doubt ill be competing in door to door action in the near future, its more a time attack setup so not going to be on track for extended periods of time. I might do dutton rally etc in the future though.

Now the question is what size to go for, i want a smaller one if possible but dont want to be refueling every 5 min because its too small?

Im thinking if i go small enough i dont need a surge tank as well or should u always run a surge tank setup?

is it best to get one with a sender setup in it as well?

at the moment im leaning towards a 30L one, so i assume a surge tank is a definate yes for this size?

If running a surge tank do u just run an external lift pump (bosch 040?) and then that feeds the surge tank (couple of litres in size?) then to my 2 bosch 044 pumps then to the motor?

any info on peoples setups in race cars appreciated

Edited by unique1

Surge tank may be the better option i had fuel surge with a 35 litre tank.

Also maybe the only way you will connect 2 044 pumps into the system as each should have its own - 6an supply, would be quite difficult to run them with only one low pressure outlet between them

if you have a read through Duncans R32 build thread you will see some fuel tank/surge tank discussion that youl find helpfull. but in short if you are running a cell with no internall pumps, you will need a surge tank/lift pump setup. . unless you modify tank to run internall pumps with a sump or baffles.

i am trying this in my car. have modified fuel cell to house 2 040 bosch pumps to eliminate the need of a surge tank, but it is untested a this stage.

Hey guys i dont know if this is the correct section, but im building up a track gtr and planning on circuit work on semi slicks and drifting as well with another engine setup and rwd, the motor is pretty serious (over 550rwhp) so i need a fair bit of fuel. I am gonna go straight for a fuel cell instead of using the original tank setup. I doubt ill be competing in door to door action in the near future, its more a time attack setup so not going to be on track for extended periods of time. I might do dutton rally etc in the future though.

Now the question is what size to go for, i want a smaller one if possible but dont want to be refueling every 5 min because its too small?

Im thinking if i go small enough i dont need a surge tank as well or should u always run a surge tank setup?

is it best to get one with a sender setup in it as well?

at the moment im leaning towards a 30L one, so i assume a surge tank is a definate yes for this size?

If running a surge tank do u just run an external lift pump (bosch 040?) and then that feeds the surge tank (couple of litres in size?) then to my 2 bosch 044 pumps then to the motor?

any info on peoples setups in race cars appreciated

post-20078-1222003049_thumb.jpg

post-20078-1222003163_thumb.jpg

Edited by BezerkR32

the tank is off the shelf but the sump with the 2 intank pumps is custom, as well as the feed lines being plumbed through the side of the tank into the inline filter.

LOL same tank i had!

thanks for the info, i went to the local track yesterday and had a look at some other cars racing and talking to the drivers and they reckon they are using around 17L in the 8 lap races so a 30L tank is probably the best size for me, i dont want too big or i might as well leave the stock tank arangement in. My other car with the engine im gonna use is running twin Goss intank pumps feeding to a 3L surge tank and then 2 x 044's into a single 1/2' fuel line to the motor.

The 2 goss pumps would still be ok on the low pressure side of the surge tank even if not submersed (sp?) in fuel? I might use them instead of the single 040 as mentioned.

Running the lift pump is the same as running intank pumps setup wise isnt it? just need small low pressure pumps to feed surge tank and then the 044s for the engine supply is ok? it wont suck the surge tank dry will it if its been ok in the current car and running same power?

cheers

yeh, this is of upmost importance. ive run carter 14psi lift pumps for surge fill with Bosch 984 pressure pump and never emptyed the surge, but fuel return was always plumbed back to surge tank, then overflow back to main tank.

as long as your fuel return is plumbing into the surge tank should be ok
  • 1 year later...

sorry to dig this up.

in regards to the overflow line, does it matter if it goes from the top of the surge to the bottom of the fuel cell?

im not sure if it will be able to drain this way or doesn't it matter due to the system being pressurized.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...