Jump to content
SAU Community

Recommended Posts

hi guys, just need some info. have just purchased a 32gtr and it was running rwd as it had broke the standard front shafts.

now i have purchased the front shafts but need to know if there is supposed to be a spring o-ring or a circlip in the position on the pic attached.

thanks adam

post-14389-1222582613_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/237955-gtr-experts-need-some-info/
Share on other sites

i know this is prolly a lil annoying but i like to know what im doin b4 i start... will i find the circlip just in the bottom of the casing or will it be cought up in something. also is there supposed to be a gasket on the housing or will it be purely sealent only and tolerence fitment. and finally what should i be refilling the transfer case with as this is the first time i have had to deal with the gtr system... thanks for your help mate.

so i took the diff cover off and found the remanance of what looks like a spring o-ring (thought id find a circlip??) just need to know if this is what locks the shaft in place. any answers would be appriciated as i need to send my wife over tomorrow to the local cv shop to get one

thanks adam

Yes, the spring o ring is it, as for the diff oil I use Red Line Lightweight Shockproof with no issues, its not cheap though and there are other options out there, best to call a workshop on that one. No there is no gasket on the cover, just the sealant.

Ok, might be wrong here, but I thought the circlip lived in the diff. That's why the shaft has a chamfer on the end - so the circlip can slide up and over the shaft and pop down into the groove.

Ok, might be wrong here, but I thought the circlip lived in the diff. That's why the shaft has a chamfer on the end - so the circlip can slide up and over the shaft and pop down into the groove.

Yes thats right, the shaft slides in the diff and gets locked in place by that circlip which sits on the end of the shaft inside the diff

Yes, the spring o ring is it, as for the diff oil I use Red Line Lightweight Shockproof with no issues, its not cheap though and there are other options out there, best to call a workshop on that one. No there is no gasket on the cover, just the sealant.
Yes thats right, the shaft slides in the diff and gets locked in place by that circlip which sits on the end of the shaft inside the diff

hey mate a lil confused, these two statements kinda contradict each other... is it a circlip that is located in the spline inside the diff center (thats what old mate at the cv shop said today... or is it that spring o-ring that i found the remainds of last night (the guy at the CV shop said that it was more likly to be from the seal that shaft goes through.)

Had em out a couple o times. The spring clip compresses in the groove of the spline as the spline is taken out of the diff, it is supposed to stay in the grooved part of spline. Then it springs back out a little once out of the diff.

It would of come off the spline due to it being: worn, stretched out or bent or just by chance it got pushed off instead of compressing upon removal.

Anyone confused at my explanation :P I'm going to bed!

I just went through this myself... I just fully rebuilt both inner and outer

cv's and came across the same problem.

I'm glad someone found out for sure that the circlip is on the shaft.... I put mine back in without a circlip... I was told alot of people do with no problems. Its not like with the

cv bolted and locked in place a Circlip is going to make much of a difference right? ....

Also what is the capacity of the front diff? 1L? also where do you get your redline? cost?

I was going to go for the motul gear oil.

cheers

rob

Yes, the spring o ring is it, as for the diff oil I use Red Line Lightweight Shockproof with no issues, its not cheap though and there are other options out there, best to call a workshop on that one. No there is no gasket on the cover, just the sealant.
  • 1 year later...

mother fu**er lol

i took my sump and shaft to a "reputable" workshop

they said the circlip was supposed to stay on the shaft. so they pulled the diff apart and took the circlip out.

the sump is back on the engine and the engine is back in the car. i tried to insert the shaft into the diff but it wouldnt go in. the circlip stops the shaft from going in.

its now ridiculously obvious that the circlip is supposed to stay in the diff.

they charged me $80 to remove the circlip.

i have the receipt. but how do i go about getting the cir clip put back into my diff? as i said the sump + diff is back on the car. and the only way i see the cir clip going back in is if i take the engine out and pull the diff apart.

should the workshop fix my problem?

is it ok if i put the shaft in without the circlip?

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...