Jump to content
SAU Community

Recommended Posts

itll flow better make more power, probably get abit more boost on the stock solonoid if you still run it, sound nicer and be louder.. if you get a half descent cat aswell it would more than likely have better emissions aswell as your old cat would more than likely be a fair bit past its used by date

those cheap 3 inch xforce cats for 175 do the job for a budget job.. you can get better ones with metal cores that flow more for around the 400 mark

a full 3 inch exhaust will be the best bang for buck upgrade youll ever get from your car :cool:

Link to comment
https://www.sau.com.au/forums/topic/238576-removing-cat/#findComment-4170193
Share on other sites

Benefits. If you have low flow cat you will pick up some HP..and flames

Debenfitis. That's not a word..but marks for being creative :blush: . The car will probably spew nasties out the tip and I believe it's quite a big fine for attempting to ruin our fragile planet

Pick up used cat, gut it and run a piece of pipe through. At least that way if they have a look you've got half a chance. Not that I condone breaking the law

Link to comment
https://www.sau.com.au/forums/topic/238576-removing-cat/#findComment-4170786
Share on other sites

just thought I should mention mate, you have a white car.... so do I.... I gutted my stock cat and put it back in...flowed that much better.... got a decent amount of extra power.... BUT... because our cars are white and the petrol company's put "cleaning agents" in petrol... the carbon monoxide that is normally filtered from the cat now comes straight out the back.... its a yellow residue that after about a build up of a week or two will make the back of your car completely poo yellow.... which you then have to cut and polish off or use waterd down degs... any more then two weeks if a cop picked u up and knew anything about exhausts would give you a good slap even though you appear to have a stock cat in there...(big fines so I hear)

in conclusion I am now sick of being paranoid, sick of cleaning it constantly and sick of the horrible yellow... so I am going to spend the cash and get a nice highflowing metal cat and done is done!

btw.... I also have had a cheapi xforce highflow... going from a gutted cat to that was a big loss of power...if I was you... either gut your cat for the cheap option or spend the cash on a metal core.

Adam

Link to comment
https://www.sau.com.au/forums/topic/238576-removing-cat/#findComment-4172179
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, sort of blurring two different things together, aren't we? I just meant O2 feedback closed loop. I used to have a 0-1V LCD meter on my dash, wired directly to the O2 sensor signal. So you could easily see what it was doing. Normal running it would flick back and forth nicely. Slow down to an idle and it would keep flicking, as the ECU tried to servo to maintain stoich, but it would slow down as each swing happened until it would stay at one end of the scale. As I said above, the sensor heater is not enough to keep it hot enough when there is also little heat in the exhaust flow. Give it a blip and it would start swinging again, then peter out again. Meanwhile, idle speed control would run just fine, because unrelated.
    • It's not even O2 feedback, it's just simply when the ECU sees the closed TPS signal for whatever reason the idle will start steadily dropping until the engine dies. With the TPS adjusted to not trigger closed TPS it will idle at some ridiculously high RPM and something like 6 degrees of timing. In the absence of getting eyes on it personally and a lot of quality time doing diagnostics I couldn't tell you what the real problem was but it was interesting nonetheless
    • Oof. One of my mates has an R34 GT-R that he initially was a "I want to go twins for response and convenience" on his stock 2.6 with Kelford 272 cams, but his friends are pests and were always in his ear about their place being in the bin.   Eventually one of the 2860-5s decided to add it's own input and force his hand, so he conceded and went for a Pulsar 6262G ("G35 900") with T4 0.85 hotside.    Here's an overlay of the results, same cams, same stock bottom end, same boost, same fuel, just from a pretty tidy 2860-5 install to a Pulsar turbo on a 6boost maniifold on BP98.   Worth mentioning here, it may seem like a dead horse thing but the dyno plot doesn't tell the story of how much better it is to drive - transient response has completely changed the car, he used to have flat foot shifting to stop it having to wind up again on gear changes even at >7000rpm... now it builds boost faster than that even short shifting.   It's 100% transformed the car before you even consider how much better it holds on: Pulsar and Garrett aren't the same, but from our experience if you're just looking for a better drive and the ability to make the same or more power I think the divided G30 770 would probably be the smallest I'd go to.
    • Great work Duncan, any events local you will give it a test once all done? 
×
×
  • Create New...