Jump to content
SAU Community

Recommended Posts

Hi!

There will be snow i Norway soon, so now im going to do a oilservice before i put it away for a couple of months.

My brother works at a local benz dealer, so I`ll get 50% off castrol oils.

What do you recomend i use in the gearbox and in the reardiff?

Im going to use castrol edge 0/40 in the engine.

I have seen that redline if often recomended, but i dont have an 50% discount on redline. And if im going to use it i have to order from us og england (expensive)

Link to comment
https://www.sau.com.au/forums/topic/238914-gearbox-and-reardiff-oil/
Share on other sites

Straight out of the Castrol website using their lube selector. This is for a R32 GTR btw, I don't think the 33 GTST is listed there. Faily sure they are the right ones, but you may want to call Castrol to confirm.

Engine:

CASTROL EDGE SPORT 10W-60

Gearbox

CASTROL VMX 80

Power Steering

CASTROL PS FLUID

Diff

CASTROL EPX 80W/90

4WD Transfer

CASTROL TRANSMAX Z

Edited by __PhaseShiftDown
  • 2 years later...

syntrax for gearbox and diff. GT-T with the standard viscous LSD will be fine as viscous is a sealed unit. If you have A-LSD then you need a diff oil with friction modifiers in it.

definitely go synthetic. I had motul gear 300 in my diff and after 80,000km and a couple of texi days I dropped the oil and it was still honey coloured and smelled great.

syntrax for gearbox and diff. GT-T with the standard viscous LSD will be fine as viscous is a sealed unit. If you have A-LSD then you need a diff oil with friction modifiers in it.

definitely go synthetic. I had motul gear 300 in my diff and after 80,000km and a couple of texi days I dropped the oil and it was still honey coloured and smelled great.

ok thanks but the LSD fluid is slightly thicker would that matter

ahh and also how can i tell if i got a LSD or a viscous LSD ?

  • 1 month later...

for 32R diffs, is there a difference in oil used between front and rear diff

i see CASTROL EPX 80W/90 is recommended by Castrol however other threads also recommend Castrol SAF-XA Limited Slip Rear Axle Oil - 80W-140 (apparently due to different conditions between Jap and Aus)

Hi!

There will be snow i Norway soon, so now im going to do a oilservice before i put it away for a couple of months.

My brother works at a local benz dealer, so I`ll get 50% off castrol oils.

What do you recomend i use in the gearbox and in the reardiff?

Im going to use castrol edge 0/40 in the engine.

I have seen that redline if often recomended, but i dont have an 50% discount on redline. And if im going to use it i have to order from us og england (expensive)

can you get Motul Ow 30 or say Agip 5W 30

on the topics of gear oil, I just had my GTR gearbox rebuilt with new synchros and seals. It has a OS Giken gearset in it and I am still contemplating which gear oil to use . . .

I am deciding out of Redline Shockproof Light and Royal Purple Max Gear Oil. Any recommendations on these two??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...