Jump to content
SAU Community

Recommended Posts

Well I finally got my stroked rb20 running yesterday but as soon as it started could hear she wasn't firing on all cylinders, We tested the injectors there all clicking away, took annd the coilpaks out and earthed them all with the plus in them and spun the CAS and they all spark.

I am stuck for ideas why its not running correctly, can anyone shed any light on why or what could be causing this to happen ?

Cheers

Cameron

Link to comment
https://www.sau.com.au/forums/topic/239019-r32-running-on-4-or-5-cyl/
Share on other sites

Igniter? coil harness?

Did you unplug each coil one at a time to narrow down which cylinders weren't firing?

Of course Bubba,

Tried each injector, and each coil pack on top of the engine and they all sparked.

Number 3 isn't firing whilst unplugging while running the engine.

Yes but they all don't cover all the injectors working fine and all the coils sparking and all brand new plugs and it still does it.

is the spark a good spark or just a spark, as if the coils are worn or the harness is stuffed they will still spark yet not properly, also have you checked the timing?

Coils are brand new used them for all of 1km driving before the engine came out. I am thinking its in the harness or the ignitor I had a quick search but is there nay way to test the ignitor?

Timing is spot on the mark.

Yes but they all don't cover all the injectors working fine and all the coils sparking and all brand new plugs and it still does it.

The principles are the same.

Number 3 isn't firing whilst unplugging while running the engine.

If #3 isn't working, then they are not "all fine". To repeat the several squillion threads, it's simply a matter of moving / swapping component locations to determine which part of the system is kaput.

And to add, We have switched the coilpacks around and the problem stay on number 3, we have also switched the injectors around.

I have read countless threads where Coilpacks are stuffed or sparkplugs are fouled up..

This case is different, I have even tried 3 sets of brand new spark plugs, 2 sets of coppers and 1 set of iridium's

We tested all the coilpacks at once but earthing them all along the top of a peice of steel earthed ot the car all of them fired when rotating the CAS, we did similar with the injectors only plugging one in at a time and spinning the CAS they all make the clicking sound when they fire.

I wouldn't of made a new thread if this was like the "squillion other thread"

The things I am yet to try is a different ignitor and different harness but have tested continuity from the ecu harness to the engine bay and all check out fine even while jiggling the harness looking for loose or broken connections.

And to add, We have switched the coilpacks around and the problem stay on number 3...
We tested all the coilpacks at once but earthing them all along the top of a peice of steel earthed ot the car all of them fired when rotating the CAS,
These 2 statements don't correlate. Either they all work, or #3 has a problem. Which one is it?

Yes, This is why I don't know why its not firing... They all sparked yet when you run the engine number 3 doesn't fire this is my problem.

Understood that if the coilpack didnt make spark to try another and see if it sparks, but what happeneds if it does spark? and changing to another coilpack still provided the same spark yet when its all on the engine it doesnt fire it?

Ok, so while you are testing the coils, they are at a different angle to when they are "installed". That might suggest a fault in the wiring to #3 coil. Have a play with the wiring to the coil while the engine is running, see if that has any effect.

Ok well, Seem to have found the problem being the number 3 injector... I took it out because it wasnt functioning.. put 12v on it no clicks... tapped it a few times tried 12v again and it started to click again. Hopefully when I put it back together it all works fingers crossed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...