Jump to content
SAU Community

Recommended Posts

Hi, i get a rattling sound -I think its coming from my exhaust- at about 40k's.. when im revving it.....

when its on neutral it doesnt make the sound, only when im driving... i recently got my cat converter replaced so its not that, my muffler replaced (i thought it was that but it wasnt) so now i have no idea what it is and my mechanic doesnt know either.. any ideas? thanks

You would think itd be something like that, theres not much else it could be if its comming from lower areas near the exhaust :S

You said you replaced the cat and wasnt that, did they check the piping from the extractors etc? maybe something isn't holding/stuck there.

But the word rattling in general is quite broad without hearing the noise for ourselves...is it a deep rattling noise? A tinny rattling?

I don't know much myself but if it doesn't happen when your idling but happens around 40km/h and continues it could just be that a section of piping is loose and not held in place properly, and when more pressure is passing through, the noise therefore occurs??

I could be waaaay off the mark. Goodluck hope you get it resolved soon!

mines doing the same aswell and its a r33 like all of you, i sware it comes from the gear box........

i think it is bearings somewhere that are worn down?

the sound and where its coming from sounds like a bearing, are all of you getting the same rattle from the gearbox thats really deep at 1500rpm and once it hits 2000rpm its more of a quiet tin rattling sound then stops after 2000rpm.

anyone confirm that they think its bearings now

yeah. sounds like a deep rattle O_O it sounds like its coming from the exhaust to me (but it aint cos i got it checked out) Anyone HOW MUCH DOES IT COST TO FIX MORE IMPORTANTLY? aNYONE KNOW? APPROX?

I'm getting the exact same problem in my R33 SI GTS-T..

I just finished installing a FMIC (which was a bitch, damn clamps flying off) and only just started noticing it now that I'm listening extra carefully..

I did some diagnostic and noticed that if I push my clutch in while it's rattling the rattling immediately stops. I was in second gear, stock ECU.

Edited by Alinys

if it stops when you put the clutch in it could be the trust bearing but id be dam soprised if you could hear that making noise while ur actually driving! when sitting there ideling you can normally pick it because it will sound like something mechanical rattling around and when you push the clutch in it stops.

but i doubt it would be a thrust bearing.

changing the clutch and all components of the clutch soon (after my 50thou rebuild is back together in a week :P ) so ill soon be able to see if it helped me or if its a problem that nothing to do with manual and auto differences. it might be the cat r the muffler because there relatively close to the gearbox to be mistaken because its just a crazy noise =\

i got the same problems, with the stock muffler it was loud on take off. it rattle hard.

thought it was a broken muffler so i got a a cannon it was still there wasnt that loud tho. i was thinking it was the cat or the resonant

seriously its going to be the clutch or gearbox. THE SOUND IS A DEAD BEARING!!!!!!! thrust bearing probity auto or manual i guess its got to be the same component, that is if were are getting that noise that we all say we have. someone take phone and record it. my car has no engine in it at the moment because of mods so i cant :)

thrust bearing probity auto or manual i guess its got to be the same component

I think you will find that only manuals have a thrust bearing as it only works when with the clutch, i know the noise im talking about is not the thrust bearing as that is making a different noise :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...