Jump to content
SAU Community

Recommended Posts

Hi all, yes i do realise there is a number of threads about idle issues which i have read through but none of them come out with a successful solution. I have an r33 series 2 rb25, the car will usually have that hunting issue where its going between 0 and 1000rpm, sometimes it settles at idle and other times it will just stall. I have cleaned out the iac valve completely, replaced the gasket on the iac valve and secured all hoses i have touched and it hasn't made any difference at all. Does anyone know what to do to fix this?

Link to comment
https://www.sau.com.au/forums/topic/240711-stalling-idle-troubles-any-ideas/
Share on other sites

disconnect battery (bolt attaches to boot frame)

pump the brake pedal a few times

reconnect battery (bolt attaches to boot frame)

start car and let idle

it should sort itself out

if it doesnt go see a mechanic

base timing etc is probably whack

should be 15det BTDC at idle

i'm still tipping vacuum leak.

there are numerous hoses that might not have been checked from the front of the plenum to the carbon canister and under the cross-over pipe. this is worth another check. apologies if you have checked every single one.

i'm still tipping vacuum leak.

there are numerous hoses that might not have been checked from the front of the plenum to the carbon canister and under the cross-over pipe. this is worth another check. apologies if you have checked every single one.

you would hear a vacume leak though.... i did with mine.....

clean afm, change plugs,clean throttle body, do you have standard bov? i recon the most important culprit is the 02 sensor..... that $70 f#&ker stuffs things up when not working,,,,,, fixed my idle prob and now gives me better fuel economy...

sure it will paul.

i have had at least 4 deteriorating hoses on my car (over the years) and i have lost count of the cars of friends with splits in various vacuum hoses that hunt at idle. immediately idling fine after replacing the hose or trimming it back.

the last time i got the car back from the panel shop they forgot to reconnect one of the hoses to the carbon canister but due to its location under the snorkel it was a job to find in the dark with a little torch.

does the vehicle have any mods firstly and does it blow black smoke from exhaust at idle. if so make sure you have not blown an intercooler pipe. also could be a faulty afm. hope this helps

its fairly stock, apart from front mount intercooler and boost controller, it doesnt blow any black smoke at idle. im going to look into checking the error codes i was given that idea by a friend.

disconnect battery (bolt attaches to boot frame)

pump the brake pedal a few times

reconnect battery (bolt attaches to boot frame)

start car and let idle

it should sort itself out

if it doesnt go see a mechanic

base timing etc is probably whack

should be 15det BTDC at idle

thanks il give that a go tomorrow. theres a place near me called rpm performance north of brisbane, so that was my last resort if i couldnt sort it out myself.

you would hear a vacume leak though.... i did with mine.....

clean afm, change plugs,clean throttle body, do you have standard bov? i recon the most important culprit is the 02 sensor..... that $70 f#&ker stuffs things up when not working,,,,,, fixed my idle prob and now gives me better fuel economy...

il give this a go tomorrow as well. the bov is stock. after i try all this if im still having problems, il look into new 02 sensor.

$20 its the 02 sensor, especially if it hasnt been changed...... diconecting it wont change a thing if its not working in the first place paulr32...... what ever it ends up to be is just general standard maintenance anyway..... alll these things should be done anyway

  • 7 months later...

PLEASE HELP!!!!!! :)

Im having the same problem with the idle fluctuating (hunting). changed plugs cleaned iac throttle aac etc etc and it hunted usually between 1500-500 just changed the coils to splitfires now it does it 1000rpm-2000rpm. it isnt consistent it is intermitent. also car will just stall when clutch has been pushed in (giving it to it or sensible driving) checked ALL Vac lines aswell. also some times it will rev to roughly (i say that coz its never on the same spot its a bitch of a thing to trace) 3500-4500 and before i changed the coils it misfired then until the boost climbed it wouldnt rev anywhere near as quick then slingshot me (very dangerous in the wet) now after the coils are changed it does the same thing but it doesnt sound like its missfiring its alot quiter but same feeling NOTE: day night rain hail or shine it will do this problem sometimes does it when the car is cold but definatly when it has warmed up. sorry for the billion words hope it makes some sense

car details:

Series 1 r33 manual gtst

RB25det

splitfire coils

standard ecu

afm looks good and clean

vac hoses checked and some replaced

standard BOV

t4 turbo (was on the car when i bought it) standard exhuast manifold

standard exhaust

also just one more thing if someone has a couple of pics of a stockish engine bay can they post them

Edited by Melbourne93R33
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...