Jump to content
SAU Community

R33 Gtr Aftermarket Rotors And Calipers

GtrVspec
 Share

Recommended Posts

GtrVspec Collaborator

GtrVspec

Posted
Posted

Hey guys i am looking at putting on new and better rotors and calipers on my gtr.i was told to get wilwood kits and that they are the best but pretty pricey. I dont think its worth getting the best but i dont want to get an ok set i would like something that is going to have the stopping capacity and last a while not 6 mnths. The car will see track in the near future but would be a 50% road and 50% track. what other brands are the ones to go with ? and what else is involved with better rotors and calipers ? like do i have to change any oil lines or type of brake fluid ? that sort of thing ?

cheers.

Roy Grand Master

Roy

Posted
Posted

Willwood make great calipers and they make cheap made to a price stuff. They make too many calipers in my opinion and relegate themselves to the too hard basket unless you have really dont your homework. Their good stuff is good but as you said expensive.

Budget is king with brakes, consider what you are willing to spend and go shopping, as budget will dictate. New you will be looking at up to 4k for fronts and similar money for rears, but common rear upgrade is just the GTR Brembo, or the N1 rear which uses bigger rotors again with a similar Brembo two piston caliper.

The 50% track and 50% road thing is all in the pad selection. If you have enough rotor to dissipate the heat then you can get away with a pad that may do both...but the trade off is wheel size requried to run brakes, whih means expensive rubber, more unsprung weight etc etc. So, finding the right brakes at the right price sux :D

GtrVspec Collaborator

GtrVspec

Posted
  • Author
Posted

i assume when u say gtr brembo theyre from the brembo brand ? iave got which look like dba ones on the front but theyre on the way out and stock on the back so i mite investigate the brembos.as for price. i dont like to put a price on brakes. i need them to stop so to me its worth spending the extra money on something good. but thanks for the advice.

GtrVspec Collaborator

GtrVspec

Posted
  • Author
Posted
But what power is your car making? What tyres, what wheel size what suspension? You may find that being an R33 that you can get away with good quality pads and decent vented rotors, at a minimum DBA5000 but preferably something better

atm its around the 400 450hp. have standard suspension though i want to fix that at the same time as brakes etcc. tyres are 275 all way around falken fk452's something like that.

Roy Grand Master

Roy

Posted
Posted
atm its around the 400 450hp. have standard suspension though i want to fix that at the same time as brakes etcc. tyres are 275 all way around falken fk452's something like that.

Considering the tyre and suspension, i would suggest you just get some good pads, and good fluid. Remove the dust shields and consider some braided lines. Though as Lotus will suggest...dont let me anywhere near youcar come fitment of said goodies :/

Spend you money on better suspension rather then too mcuh on brake hardware. If your rotors are shot then consider some DBA 5000 or preferably direct replacement 2 pce Endless or Project U rotors. As for pads i have really liked Endless CCX, though its possible they are hard on rotors. Though my car having problems with DBA 4000 and RDA rotors and the CCX pads is hardly enough evidence to support that theory :(

Roy Grand Master

Roy

Posted
Posted

I trial fitted them to my car. Nice kit, basically an AP kit, only you need to make sure you get the 355mm kit and not the 330mm kit. Difference being the 330mm kit is 26mm thick and the 355mm kit is 32mm. On an S13 etc the 26mm thick rotor may be ok...but on larger more powerful cars you really want the extra width in the rotor...i think:) They have a loyal following and i will admit the rotor hats are beatifully designed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      ECU sees many times the speed than speedo does (R34 swap)

      By Kapr · Posted

      The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Duncan
      Who has a Infiniti Q60, Q50 (V37)?

      By Duncan · Posted

      Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...