Jump to content
SAU Community

Recommended Posts

Item: Genuine JDM Nissan Skyline R32 GT-R nismo boot lip spoiler

Age: came off a 1989 model gtr

Condition: good with no visible scrathes or cracks

Price: $250ono

To Fit: (What car) r32 gtr, gtst or whatever r32

Location: melbourne

Contact: tony 0412862091

Comments:

hey guys i got this genuine jdm r32 gtr nismo boot lip spolier for sale, i purchased it not long ago but have decided not to put it on due to so much stuffing around and dont really hav the time to do it, its a genuine jdm nismo spolier and it is in gunmetal colour, these cost heaps as they are genuine so get yorself a great buy and look absolutely fantastic when fitted

cheers tony

0412862091

post-42095-1224470330_thumb.jpg

Edited by GTRBOS
damn i love this spoiler...wish i had this instead of a gtr spoiler =(

well get it then hehe as its grey like your gtr,

price is pretty much firm guys

cheers tony

Hey buddy. I might be interested if the price was lower. Also where are the holes for the bolts?

Cheers

hey mate how you going, amm the price is pretty much fair i really think, let me know

cheers tony

guys there are no holes in this spoiler as it was securely fitted with double sided tape and i think thats what most people use to fit these spoilers on, come on guys so much interest but no buyers

cheers

it's not genuine. there is no cut outs to allow for the stock wing. so definately not genuine, and not nismo. sorry. :)

well i was told its genuine, here is the information when i first purchased it

Nissan Skyline GT-R Boot Lip Spoiler

What you are looking at is a JDM Nissan Skyline R32 GT-R boot lip spoiler.

Removed from a 1989 BNR32 Nissan Skyline GT-R, however will also fit the GTS-t and GTS model R32 Skylines.

This spoiler comes in grey however could very easily be re-sprayed to match any colour Skyline.

All-round this item is in used but beru good condition with no visable cracks or breaks.

Looks great when fitted !

Tony, it is what is known as a Type 2 N1 Style Boot Lip Spoiler.

You cannot refit the factory wing if using this lip, and it is definately not a Genuine Nissan part.

thanks for that guys, if its not genuine then its not but you did read what it said about it,

anyway guys im open to offers on this and yess i guess the wing will need removing if putting this wing on but will look mad as its got no cut outs and will look good if only n1 boot lip on, anyway guys make me an offer and take it because i need it gone as its not going on my gtr

cheers tony

I would buy it but as stated it's not a genuine Nismo and your reasoning for it being so pricey was that it was a NISMO item, so i think you should adjust the price accordingly.

Also is this fibreglass or rubber?

well you wont mate, on the ebay add i forgot to mention advertised elsewhere so can end auction at any time but that was my mistake

cheers tony

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
×
×
  • Create New...