Jump to content
SAU Community

Australia Deploys Noise Cameras

d00dz

By d00dz,
in New South Wales

 Share

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

siddr20 Grand Master

siddr20

Posted
Posted

Yea from 3 to 2 lanes just past the truck inspection bay.

But there is a flash unit behind it. I think its a speed camera, but the camera full points towards the other side of traffic. Check it out next time and see for yourself.

I drive to gong nearly everyday so i will keep a look out for a new speed camera sign (if it is a speed camera)

YLD-CHLD Collaborator

YLD-CHLD

Posted
Posted (edited)
Comes to a point where you just say no more..

I want to take an angle grinder and go to work on as many fixed speed cameras as I can.

I agree lets cutem down!just another revenue raiser.

If they where serious they would make the vehicles attend the RTA to qualify the defect, then get repaired the said problem.

Edited by YLD-CHLD
Neil Grand Master

Neil

Posted
Posted

I think they are targeting trucks using compression brakes,,,not us. Let face it,,,going down Ousley would normally be done on a trailing throttle,,,no skylines going to break the limit of a noise box.

Oh and some of my good old friends are bikies,,,sure their bikes are loud,,,but they are cool dudes.

Neil.

scathing Grand Master

scathing

Posted
Posted
hard to pin a recording of air brakes on a particular truck...

From what I've read, the system uses several microphones. If they're directional enough, it shouldn't be impossible to triangulate the source of the noise.

Putting it on Mt Ousley Rd, on such a steep section of road, is just bollocks if you ask me. There's not much by way of housing out there, and there's sound barriers, and I'd rather there be a little noise than trucks having no brakes at the bottom of the hill.

DRD-00F Grand Master

DRD-00F

Posted
Posted
From what I've read, the system uses several microphones. If they're directional enough, it shouldn't be impossible to triangulate the source of the noise.

Oh trust me, I know how that part of it would work :)

My point is, you would still need a picture of the vehicle in question. You can't just play back a recording and be like, "I put it to you mr trucker sir, that these ARE your air brakes..."

scathing Grand Master

scathing

Posted
Posted
My point is, you would still need a picture of the vehicle in question. You can't just play back a recording and be like, "I put it to you mr trucker sir, that these ARE your air brakes..."

The system takes a 10 second video recording to go with the audio and triangulation data.

scathing Grand Master

scathing

Posted
Posted
Wonder how many DB a joint fart can produce.

I reckon we just find out where the mics are, and just set up a birdseed tray in front of them.

Some of those birds make a massive racket, and if the government tries to shoot or poison them all those nature types will kick up a massive stink.

Bonus points for someone who can figure out how to make a kookaburra shit on the camera lens.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...