Jump to content
SAU Community

20/12/08 Willowbank Pre-test N Tune Session - 3 Hours


Recommended Posts

Im in for sure! Been waiting for this to get posted up :) Can't wait!!

It's gonna be my first time doing a 1/4 as well. So i'll be hopeless for sure! hahaha

Oh also just wondering....prob a dumb question.... but is there a tyre pressure guage thing at the track or do i need to do my tyres before i get there??

same here :O come line up with me

wont look so bad

  • Replies 219
  • Created
  • Last Reply

Top Posters In This Topic

What happens if more than 30 people want to go? I guess it'd be a waste casue there wouldnt be enough time to get many runs in. Also do you pay at the gate or is it pre paid

We will organize payments closer to the date. At this stage it’ll be payments deposited into the SAU QLD bank account to lock in your spot on the list.

We want to keep it to 30 cars so everyone gets plenty of runs!!

In so far:

1) Bunta

2) Wagamama

3) toddlls

4) Pear

5) DAS KAMU

6) and3_3

7) Shanef

8) Jayson

9) Fine Line

10) NA 33

11) Socko

12) Rhinorebel

13) Blitz_R33

14) Blitz_R33 (friend)

15) Strik3r

16) Lazy-Bastard

17) ToMMaH (MAYBE)

18) DiRTgarage (MAYBE)

19) trust33

20) 116.hks

21) Col-GTSX

22) si_ (MAYBE)

23) 85URK (MAYBE)

24) 9krpm (MAYBE)

25) spilmer

26) Eug (MAYBE)

27) Hell Fire (MAYBE)

28) jase-r34

29) impact_blue

30) 2BNVS

So how many runs would you normally get at a TnT??

If you got there at gates open and you kept returning to the line and lining up again on a normal night maybe 5 or 6 runs...

It all depends on how many people damage the track (oil spils etc)... Also depends on how many are there...

But all factors considered 5 or 6 would be a average...

So this event with 3 hours and 30 cars could be like 20 runs at least... Given you return to line up again straight away and no one drops oil...

Given a normal night costs $38 for 5 or 6 runs and this is $48 for heaps more, I cant pass up this sorta value... :)

I've had as little as 3 runs and as many as 15 at a test and tune. Depends on the numbers.

30 cars is not may. You will be surprised how quickly they run through. Budget for about 2 cars a minute once its up and rolling. It will be bloody hot so the more cool down time between runs the better.

I would say you could comfortably handle up to 50 cars and every body will get more than enough runs to keep them happy.

I was thinking the same thing Noel, 30 cars will mean there'll be gaps of time where there's no-one on the track, cos you do want your car to have a bit of a rest period in between. We definitely need to open up another 10 spots IMHO.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...