Jump to content
SAU Community

Recommended Posts

hey there

my GTR has a LINK G4, no AFM's, profect B.......just a question my car has the profect set on 15lbs and 18lbs, my mechanic is going to do the 'cold start' next week, i asked him if he could set the profect to 20lbs instead of 18lbs, he hasnt mapped it over 18lbs

will it have to go on the dyno to set the cold start, and would it have to go back on the dyno to map it to 20lbs? im guessing yes? am i asking a bit much of my standard internals (RB26) to run at 20lbs? rev limit set to 7400RPM, engine mint compression, no knocks etc.......

cheers

Link to comment
https://www.sau.com.au/forums/topic/242084-gtr-tuning-question/
Share on other sites

what turbos? that's the big factor you've left out.

wont need to be on the dyno to re-do the cold start. will need to be on the dyno to set the boost control properly at 20psi.

what turbos? that's the big factor you've left out.

wont need to be on the dyno to re-do the cold start. will need to be on the dyno to set the boost control properly at 20psi.

hey sorry

big ol' 2860-5.....and usual upgrades

cheers

well whether your engine can handle 20psi out of -5s is impossible to predict really. maybe it will maybe it wont. one thing is for sure the more boost and (with larger turbs) the more airflow you are putting into the engine the more likely any weakness is to show up. so it's your call really. the turbos can certainly take it no problem. if it were me and your engine is as good as you say then sure give it 20psi on the street. on the track (should you go there) maybe turn it down a bit for some safety.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...