Jump to content
SAU Community

Recommended Posts

Hello Everyone!

A few week ago I was looking at this D.I.Y >> http://www.skylinesaustralia.com/forums/To...mp;hl=stop+beep in the hope of stopping my beep - but this method only seems to work on <R33. So I opened up my baby and had a crack - and I succeeded! Very easy - very quick - and no damage to anything - it's just a simple disconnecting of a plug :)

I have Found no Side effects to any other system - I have a Auto Watch emob. and it still works fine - also this will not get rid of the beep for when you leave your lights on and open your door - also does not effect the door open lights on/off function

What you need:

RATCHET

10mm Socket

Phillips Head Screw Driver

Your Keys! <you will see why ;)

(Next 2 items are handy to have close if needed - but not essential)

Flat Head screw Driver (with double sided stick tape with one side still covered with plastic wrapping to stop sticking) < I use this to wedge open anything that is hard to open up - the double sticky tape prevents scratching because its spongy - very useful for when you need to take out air con vents on the R34 etc. as well.

And my trusty Victorinox Swiss Army Knife :)

t_0001139m_6e9c7b5.jpg

(CLICK ON PHOTOS FOR LARGE PICTURE)

Step 1: Unscrew Lower cover

t_0001138m_689594e.jpg

Left Hand Side of Lower Panel (Phillips head screw driver)

t_0001132m_8618887.jpg

Right Hand Side of Lower Panel (you will need 10mm socket)

t_0001130m_fe9c8bf.jpg

Here you will have to disconnect all Wires and thread them through any holes so you can remove the whole cover and put it out of the way

t_0001129m_73ab14c.jpg

Step 2: Unscrew Steering wheel under cover

t_0001127m_64f22cc.jpg

Open the Steering Wheel Adjustment Leave Right out so that it doesn't get in your way - also so that you can move the steering wheel up and down to help wiggle the case off

t_0001122m_be80390.jpg

Step 3: Remove the demand Beeperiser Plug

Your Undercover should look like this now - if not - you have gone astray and need to revert back to step 1 and/or you have the wrong car and revert back to top link!

t_0001118m_d25dda1.jpg

See that white plug well - Now you hear it!!

t_0001116m_559f008.jpg

Now you don't!! - Now just rap that sucker around some wires and make sure the little slider inside the plug is OFF - this is what your keys are for!! Before you go and put it all back together put the key in and make sure it is in the off position otherwise it will forever be beeping :(

t_0001115m_3ee528f.jpg

Enjoy the sweet sweet sound of beeplessness ;) and your stereo when you want to work on your car :)

If you need any help just post or Pm me :)

Aron

Link to comment
https://www.sau.com.au/forums/topic/242701-diy-stop-open-door-beep-for-r34/
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Legend :)

Will try that out in the weekend. Main motivation being the ability to listen to the stereo at low volume while working on the car...high volume kills the battery and low volume gets killed by the BEEP.

Was this trial and error for you? with all the tips involved you would tend to think so hehe..

Thanks again

  • 1 month later...

Cool thanks i just did it!!!! fantastic!

U don't need to remove the lower panels - only the steering wheel cover

Just remove the steering wheel panel (Start from STEP 2), to get to the white connector and disconnect it. Only need a philips screwdriver for the job.

  • 2 weeks later...
  • 2 weeks later...

Im Pretty sure jaycar have a kit that will have your lights work like normal (ie. still turn on without key) but turn off when you take out the key after driving, much like a commodore. Dont quote me on it thought, definantly somthing useful however.

  • 4 months later...
  • 2 months later...
Will this get rid of the annoying beeping sound when your car is in reverse?

Nope, i don't spend much time in reverse so it doesn't bother me that much. But if you do want to remove it i cant imagine it would be very hard....just find the beeper and cut the wire...

  • 5 weeks later...
  • 4 years later...

Anyone have any clue which plug I'm looking for? Pics above don't work and I've tried a few white plugs but none of them are turning the beep off. Here's a pic from under the steering column.

post-125345-0-29644500-1411784850_thumb.jpg

Too late to edit previous post, I had only tried a few plugs cause I was too scared of unplugging the airbag. Eventually worked out the airbag is the bright yellow plug so I got more adventurous with the white plugs.

The plug that controls the key-in-ignition signal is a T shape white plug on the underside of the ignition barrel. It looks like the photo below when unplugged. You can unplug the white end or the other end (small brown connector above ignition barrel) with the same result:- no ignition + open door beep, keep headlights + open door beep.

post-125345-0-32613100-1411825312_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...