Jump to content
SAU Community

Recommended Posts

its r33 40th anniversary front bar

I was under the impression that the only body option for the 40th anniversary was the GTR rear wing, does anyone have any more info on this "optional" front bar?

  • 2 weeks later...

u can buy one here in japan :0.. took me a while. but found one to buy.. well, its closer then anyone can get so far, unless you buy fron nissan :P

http://www.importmonster.com.au/view?url=h...p;title=R33%20F

like i said before > its the closest anyone will get if there after a 40th anniversary front bar!.. i have not seen a fibreglass version in 6 years, and this is the best i can find if ppl need one.. there really isent much difference in the two bars, and it is shorter in hight just like the gtr style 40th anniversary front bar, so not hitting the ground .. take a look.. it really isent that different.

lol @ wrong bar..haha.. im just giving some ppl some options with the annoying series2 front end..

heres a pic so you all can look and compare the 2 bars with pictures :(..hhehe

to me they look the same but with extra air vents on the side being a aero version bodykit. umm which makes sence to me.. people who are talented enough to look at 2 pictures at one time will see they are the same exept one thing different, a extra air vent on the side of the bar.. still lmao at wrong bar..hehe

post-21353-1226785094_thumb.jpg

Edited by seriesII

no its ROFL at wrong bar now, they look noway near the same dude.. the middle part down the bottom is different the vents on the side u mentions is different, the whole front bar is flared out like vertex style theres not lil lip vent at the bottom.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...