Jump to content
SAU Community

Recommended Posts

My tip is dont be stingy. I had the worst tyres on my stock rims, and I lost it soooo many times in the wet, just from turning a corner without acceloration. I now have tyres worth over $250 each and they are a HUGE improvement. The car will now corner faster then what I'm prepared to take it, even side stepping the clutch in the semi-wet is difficult!!

I wouldnt reccomend the Sumitomos I have on my car, purely because of the price. However, if you have the money, go for it!! Otherwise, go for the most expensive you can afford, without going over the top like I did. So many people forget how important tyres are, they are what keep you on the road!!

Good luck!! :banana:

Link to comment
https://www.sau.com.au/forums/topic/243969-new-tyress/#findComment-4249972
Share on other sites

I love the Sumitomos, and only paid just over $800 including a wheel allighment because of a trade price discount, however it doesnt break traction like the old ones :banana: And they're too expensive to burn! Never again :) But they are fantastic for the main reason why I bought them

Link to comment
https://www.sau.com.au/forums/topic/243969-new-tyress/#findComment-4249985
Share on other sites

NA :banana: but its so prruuddyy so i could never part with it haha

i was thinking about putting a turbo on, but my engine is like amazing and ive never had a problem with it so i dont wanna thrash it and ruin it :)

Link to comment
https://www.sau.com.au/forums/topic/243969-new-tyress/#findComment-4250043
Share on other sites

I was thinking the same thing, but costs too much to convert. Play around with your car for a bit, and when you get bored upgrade!!

At least you dont need to worry about boost kicking in when its wet and sending you out of control!

And I wont be the only NA on cruises :banana:

Link to comment
https://www.sau.com.au/forums/topic/243969-new-tyress/#findComment-4250055
Share on other sites

Best tyres i used on my 33 last time was the Bridgestone Potenza G3's... Man those f**king tyres stick to the road even when its really wet! I only started sliding around when theres only like 50% tread left..

They don't come cheap though.. if I have not mistaken I got a set for about $1400+wheel alignment 2 1/2 years ago...

Link to comment
https://www.sau.com.au/forums/topic/243969-new-tyress/#findComment-4250081
Share on other sites

Federal 595SS's are good tyres for a good price, I pay retail of under $200 a corner from a local tyre joint. Oh and they take quite a hammering too :cheers:

I had these on my old 33 a couple years back..

I have the 595 RS on this car, very nice but cost around double the 595 SS.

Link to comment
https://www.sau.com.au/forums/topic/243969-new-tyress/#findComment-4250829
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...