Jump to content
SAU Community

Recommended Posts

I imported my 32, and as usual the aircon condensor has been removed and degassed. i think it had the old gas in it.

does anyone know if i can take it anywhere to get it regassed or do i need to find someone who has the old gas?

a place in the western suburbs would be good. thanks for the help :ninja::laugh:

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/
Share on other sites

Yeah in compliance, they will remove the gas due to some heritage law in Australia. They should re-gas it, though?

I know Profix regas air-cons! It doesn't need the 'old' gas, it just needs to be re-gassed with whatever the workshops use.

Costs about $149 from memory.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251391
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251484
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Speaking of air cons, anyone know a place that repairs dodgy air mix door/actuators? Mines short circuited and requires a replacement

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251494
Share on other sites

adelaide car care on marion road regas for less then $100 bux

i got mine done there but found out after that the air con motor had shat itself :)

couldnt find that place :D ended up taking it to isaacs auto electricians on brighton road, had to get some valves put in (as it was missing them) and regassed and serviced. works real good now tho! cold as!

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4254561
Share on other sites

Does any1 know about the sensors linked to the aircon? I've had an auto electrition look at it and they couldn't fix they said possibly sensors behind??? Any ideas????

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255017
Share on other sites

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

But i've had everything looked at the fan works but no cold air comes out??

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255031
Share on other sites

But i've had everything looked at the fan works but no cold air comes out??

ok what u need to do is run the diagnostics for the climate control... theres a guide here somehwere

basically you hold down the 'off' button of the CC unit as soon as you turn the ignition on... after 4-5 seconds it'll start up in diagnostic mode

you can then use the up and down arrows to navigate thru the options... you'll need to read the guide to interpret them, its your best bet of figuring out whats going wrong

if your fan works it could either be a compressor not working/no gas in compressor, or a stuck hot/cold mix door.... or a bunch of other stuff .... do a search on the r32 climate control and you'll find the diagnostic thread.... mine reports a shorted PBR actuator (controls the hot/cold mix coming into the car)

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255178
Share on other sites

hey mate. if it is on r12, which is the scew type service port fittings then, you need to get it retro fitted to the new gas. the old gas is no longer sold as it not ozone friendly. the reciever drier will need to be replaced as it has been exposed to the atmosphere, and the oil changed to a R134a gas type (like ester oil) it's a massive fine if anyone is caught incorrectly gas vehicles or hasn't got a licience to do so. it costs me $100 a year for my licience so i can regas vehicles. if i was you i'd get it done properly just so the a/c doesn't completely sh*t it's self and cost you a fortune. that's my 2c.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255181
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...