Jump to content
SAU Community

Recommended Posts

I imported my 32, and as usual the aircon condensor has been removed and degassed. i think it had the old gas in it.

does anyone know if i can take it anywhere to get it regassed or do i need to find someone who has the old gas?

a place in the western suburbs would be good. thanks for the help :ninja::laugh:

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/
Share on other sites

Yeah in compliance, they will remove the gas due to some heritage law in Australia. They should re-gas it, though?

I know Profix regas air-cons! It doesn't need the 'old' gas, it just needs to be re-gassed with whatever the workshops use.

Costs about $149 from memory.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251391
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251484
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Speaking of air cons, anyone know a place that repairs dodgy air mix door/actuators? Mines short circuited and requires a replacement

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251494
Share on other sites

adelaide car care on marion road regas for less then $100 bux

i got mine done there but found out after that the air con motor had shat itself :)

couldnt find that place :D ended up taking it to isaacs auto electricians on brighton road, had to get some valves put in (as it was missing them) and regassed and serviced. works real good now tho! cold as!

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4254561
Share on other sites

Does any1 know about the sensors linked to the aircon? I've had an auto electrition look at it and they couldn't fix they said possibly sensors behind??? Any ideas????

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255017
Share on other sites

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

But i've had everything looked at the fan works but no cold air comes out??

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255031
Share on other sites

But i've had everything looked at the fan works but no cold air comes out??

ok what u need to do is run the diagnostics for the climate control... theres a guide here somehwere

basically you hold down the 'off' button of the CC unit as soon as you turn the ignition on... after 4-5 seconds it'll start up in diagnostic mode

you can then use the up and down arrows to navigate thru the options... you'll need to read the guide to interpret them, its your best bet of figuring out whats going wrong

if your fan works it could either be a compressor not working/no gas in compressor, or a stuck hot/cold mix door.... or a bunch of other stuff .... do a search on the r32 climate control and you'll find the diagnostic thread.... mine reports a shorted PBR actuator (controls the hot/cold mix coming into the car)

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255178
Share on other sites

hey mate. if it is on r12, which is the scew type service port fittings then, you need to get it retro fitted to the new gas. the old gas is no longer sold as it not ozone friendly. the reciever drier will need to be replaced as it has been exposed to the atmosphere, and the oil changed to a R134a gas type (like ester oil) it's a massive fine if anyone is caught incorrectly gas vehicles or hasn't got a licience to do so. it costs me $100 a year for my licience so i can regas vehicles. if i was you i'd get it done properly just so the a/c doesn't completely sh*t it's self and cost you a fortune. that's my 2c.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255181
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...