Jump to content
SAU Community

Recommended Posts

I imported my 32, and as usual the aircon condensor has been removed and degassed. i think it had the old gas in it.

does anyone know if i can take it anywhere to get it regassed or do i need to find someone who has the old gas?

a place in the western suburbs would be good. thanks for the help :ninja::laugh:

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/
Share on other sites

Yeah in compliance, they will remove the gas due to some heritage law in Australia. They should re-gas it, though?

I know Profix regas air-cons! It doesn't need the 'old' gas, it just needs to be re-gassed with whatever the workshops use.

Costs about $149 from memory.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251391
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251484
Share on other sites

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

Speaking of air cons, anyone know a place that repairs dodgy air mix door/actuators? Mines short circuited and requires a replacement

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4251494
Share on other sites

adelaide car care on marion road regas for less then $100 bux

i got mine done there but found out after that the air con motor had shat itself :)

couldnt find that place :D ended up taking it to isaacs auto electricians on brighton road, had to get some valves put in (as it was missing them) and regassed and serviced. works real good now tho! cold as!

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4254561
Share on other sites

Does any1 know about the sensors linked to the aircon? I've had an auto electrition look at it and they couldn't fix they said possibly sensors behind??? Any ideas????

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255017
Share on other sites

i know the locations of 3 sensors;

One is inside the centre unit, to the right of the ashtray (where there is a small air grille cutout)... thats the interior air temp sensor

then theres one on the top of the dashboard, its a black plastic shiny square on the passenger side near where the dash meets the window... that one is the sun load sensor/sunlight sensor

then theres another one in the front bumper section which is the external air temp sensor...

think there are a couple other sensors (one for the temp of the compressed gas at least) but I wouldnt have a clue where to look

If these guys are any good at fixing aircon's, I might have to take mine there... my PBR actuator is reporting a short circuit ;\

-D

But i've had everything looked at the fan works but no cold air comes out??

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255031
Share on other sites

But i've had everything looked at the fan works but no cold air comes out??

ok what u need to do is run the diagnostics for the climate control... theres a guide here somehwere

basically you hold down the 'off' button of the CC unit as soon as you turn the ignition on... after 4-5 seconds it'll start up in diagnostic mode

you can then use the up and down arrows to navigate thru the options... you'll need to read the guide to interpret them, its your best bet of figuring out whats going wrong

if your fan works it could either be a compressor not working/no gas in compressor, or a stuck hot/cold mix door.... or a bunch of other stuff .... do a search on the r32 climate control and you'll find the diagnostic thread.... mine reports a shorted PBR actuator (controls the hot/cold mix coming into the car)

-D

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255178
Share on other sites

hey mate. if it is on r12, which is the scew type service port fittings then, you need to get it retro fitted to the new gas. the old gas is no longer sold as it not ozone friendly. the reciever drier will need to be replaced as it has been exposed to the atmosphere, and the oil changed to a R134a gas type (like ester oil) it's a massive fine if anyone is caught incorrectly gas vehicles or hasn't got a licience to do so. it costs me $100 a year for my licience so i can regas vehicles. if i was you i'd get it done properly just so the a/c doesn't completely sh*t it's self and cost you a fortune. that's my 2c.

Link to comment
https://www.sau.com.au/forums/topic/244119-import-air-con/#findComment-4255181
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...