Jump to content
SAU Community

1998, R34, Manual, 68,000km's, Black, Turbo

sunnycoast-old
 Share

Recommended Posts

sunnycoast-old Rookie

sunnycoast-old

Posted
Posted (edited)

Car was purchased in April this year from Sydney and driven back to my home in Sippy Downs. Car has been garaged and well looked after. Serviced every 3,000km's with Motul Oil and Oil Filter. Car worked on by MW Performance on the Sunshine Coast.

PRICE DROP $21k - WILL TAKE ANY OFFER OVER 19,500 CASH IN HAND (with stock rims and no plates). Prepared to NEGOTIATE.

Would consider reducing price of car if performance mods were removed from vehicle. Happy to remove certain things to lower price.

Car has been run on BP ULTIMATE 98 Octane its entire life. -At present, car runs around 400-450km's per tank.

I welcome any questions and inspections on the car. You wont be dissapointed. Welcome to all reasonable O.N.O's - Reason for sale - Car is not used as often as i would like and is surplus to my needs. $22,000,Wont find a better price anywhere.

List of mods and prices of mods as follows:

Apexi AVC-R Boost Controller - $650

Apexi Power Intake Pod Filter - $89

Cold Air Induction Box - $150

Walbro 500hp 255Ltr Fuel Pump - $190

Whiteline Sway Bars, Front and Rear - $520

Cusco Rear Strut Brace - $210

Nismo Front Strut Brace - $100

Cusco Subframe Strut Brace - $150

Tien Super Street Coil Overs - $1680

Super Pro Subframe Bushes - $100

Hicas Lock Bar - $99

Full Tubro Back HKS Super Silent Exhaust with High Flow Cat - $1600

Splitfire Coil Packs - $529

Irridium Racing Plugs - $139

GREDDY timing belt

New Water Pump, Idler Bearings, Seals and pulleys. Includes new ancillary belts, 100,000km Service (done 30,000km's early) - $1,000+

Nismo Thermostat - $149

40mm Racing Radiator - $399

Cooling Pro Stealth Loop Kit Legal Intercooler - $550

XHP 18" Rims with 95% Federal Tyres - $1,900

Nismo front and Side Clear indicators - $110

B Pillar Strut Brace - Inside Car - $129

Alpine CD Player with 12" sub and 800watt amp - $600

Turbo Timer - Came with Car

Tinted Windows - $170

Nismo Gear Shifter. - $69

Link to images: http://www.carsales.com.au/used-cars/priva...amp;distance=25

PM OR CALL/TEXT on 0401637722

Edited by sunnycoast

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...