Jump to content
SAU Community

Recommended Posts

what engine? RB20 approx. 3.9, RB25 approx. 4.1 give or take. I'll check out the real figures and get back to you, but the 'real' figures never mean much. My 25 is supposed to take 4.1 with an oil filter, but your usually flat getting 3.7 or 8 in it. If it was a totally dry engine [after a rebuild maybe] then you might get the spec figure in.

Link to comment
https://www.sau.com.au/forums/topic/244440-how-many-litres/#findComment-4258226
Share on other sites

After i started mine and let it settle, the oil was about half way on the dipstick, I could maybe put another 100-200cc in and get to 3.9 or 4 litres, but thats it.

You need to borrow someone elses dipstick, but usually if you overfill, it will burn heaps of blue smoke, just blow it out in clouds. I'd have a look at your oil container, you might have purchased a 4 litre one instead of a 5 litre?

Link to comment
https://www.sau.com.au/forums/topic/244440-how-many-litres/#findComment-4262727
Share on other sites

na i was only joking...its the right dipstick..well i put 5 lt in n it was 5lt bottle n i recon it is about 200mls over which make it about 4.8 but that is rb20..i have always done this on a vl..then vl rb20 &r32 no blue smoke no problem..but 2 answer the original question jus put oil in til its up2 the full mark

Link to comment
https://www.sau.com.au/forums/topic/244440-how-many-litres/#findComment-4263799
Share on other sites

ok thanks, because i lost a shit load of oil because my sandwich plate was leaking pretty bad and it took me a week to see it (no oil temp or oil pressure changes), i was told that the oil level was still over full level but i dunno if the guy who tightnd it all up knew what he was on about seing that its still leaking....

atleast its only 1 or 2 drops in 24hrs,,,, before it was dripping at 1 drop every 3 seconds when the car was warm and idleing lol

Link to comment
https://www.sau.com.au/forums/topic/244440-how-many-litres/#findComment-4270859
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...