Jump to content
SAU Community

Recommended Posts

I have a premium coupe with Bose sound system as usual. Lately when going around corners the left speakers are dropping out. Now over some bumps the sound goes in and out. At first I thought it was just a loose speaker wire in the left hand door, but I have since realised the Left rear side speaker is doing the same thing, which I am guessing may have something to do with where the speaker wire plugs into the back of the stereo itself.

Just wondering if anyone has any suggestions before I start pulling the dashboard to bits?

Link to comment
https://www.sau.com.au/forums/topic/244823-bose-speaker-problem/
Share on other sites

two things there. the lock is a different probelm and a BITCH to change. about $300 for a new one ex japan.

the audio issue. look at the amplifer in the rear left corner of the boot. pull that out and down then look for dry joints. the radio does this as well but I have yet to see it.

the audio issue. look at the amplifer in the rear left corner of the boot. pull that out and down then look for dry joints. the radio does this as well but I have yet to see it.

Thanks for that Chris. I'll have a look at that. Now what is a "dry" joint?

Thanks for that Chris. I'll have a look at that. Now what is a "dry" joint?

If my year 10 electronics serves me correctly I believe it is something to do with fouled solder/contact points on the circuit board, either from wear and tear or from the factory

If my year 10 electronics serves me correctly I believe it is something to do with fouled solder/contact points on the circuit board, either from wear and tear or from the factory

or components that have worked loose due to vibration. considering how that amplifier is mounted I would point the problem there.

Dry joint, you need to re-heat the solder up and make sure it has continuity all the way through the joint.

If you are a bit unsure any good electrical component repair shop could do it fairly easily... or Chris I would think.

no probs. I'm between cars now (have another sedan due inthe morn) I'll take one of these amps out and take a few snaps of it for you.

if you do head down to see me - ring first.I'm not always here.

no probs. I'm between cars now (have another sedan due inthe morn) I'll take one of these amps out and take a few snaps of it for you.

if you do head down to see me - ring first.I'm not always here.

Yeah thanks.

I had a look at it this arvo, sure is a lot of wires going into the amp. Pulled out the plugs and had a look around, couldn't see anything obvious, but as a result of pulling it apart, I think the speakers down the left hand side are now sounding very ordinary (very little grunt) compared to the right hand side.

If I may make a suggestion before you rip the car apart looking for amps and shit, test something first.

When you're getting the problem while listening to a CD, flick over to the radio and see if it happens there (or any other audio source aside from the CD player if you have one). I get the feeling the problem is isolated to the CD player.

The 350Z Bose stereos have a known issue (with TSB I'm pretty sure, although I don't have it to hand) where the speakers intermittently drop out while playing CDs. It doesn't happen with the tape deck or tuner (or aux input for those cagey enough to figure out there was one), and it feels like a loose connection since hard accelerating/braking can start/stop the problem. US guys have complained about it, as have a few Australians I know. Since the Z and V share so many components, it could be a common theme.

Nissan Aus didn't even bother fixing it when 2 of my mates had the issue with their Z's. The head unit was replaced. Mine did it just after warranty expired. At first it was the passenger side (both front and rear). Then the driver's side occasionally. Then both. Then back to passenger side. I ended up using a FM tuner or tape to line-in converter with my iPod. I replaced it with a double DIN, and kept the amps and speakers stock, and haven't had issues since.

Edited by scathing
If I may make a suggestion before you rip the car apart looking for amps and shit, test something first.

When you're getting the problem while listening to a CD, flick over to the radio and see if it happens there (or any other audio source aside from the CD player if you have one). I get the feeling the problem is isolated to the CD player.

The 350Z Bose stereos have a known issue (with TSB I'm pretty sure, although I don't have it to hand) where the speakers intermittently drop out while playing CDs. It doesn't happen with the tape deck or tuner (or aux input for those cagey enough to figure out there was one), and it feels like a loose connection since hard accelerating/braking can start/stop the problem. US guys have complained about it, as have a few Australians I know. Since the Z and V share so many components, it could be a common theme.

Nissan Aus didn't even bother fixing it when 2 of my mates had the issue with their Z's. The head unit was replaced. Mine did it just after warranty expired. At first it was the passenger side (both front and rear). Then the driver's side occasionally. Then both. Then back to passenger side. I ended up using a FM tuner or tape to line-in converter with my iPod. I replaced it with a double DIN, and kept the amps and speakers stock, and haven't had issues since.

I think that's the exact reason!! When I play CD's like I mentioned above, the left side starts to cut out. Hard braking/accelerating does help the problem. I have tried to switch between the CD player and Radio and have found that it does not happen when I have the radio on. Hopefully installing a Dvd player with mp3 will work? Since it will be using the Aux setting? How else would you fix it ?

How else would you fix it ?

I dropkicked the Bose CD player into the bin, and installed an Alpine IVA-W202E.

Using the aux input should be OK, as the other two sources on my head unit (radio, tape) worked fine and I used interfaces to get my iPod to work.

Could this mean a 'Class Action' against B%SE?

Could B%SE prefer to compensate you all if you advertised in the media that...

a whole raft of people (SAUers undercover) were going to be present at a particular destination (after halfway thru a SAU Cruise) to...

SHOOT DEFECTIVE B%SE CAR AUDIO EQUIPMENT WITH A SHOTGUN !!!!!!!!

Wouldn't they prefer to pay you guys out than to LET THE SHOTGUN GO OFF!!!!! AND THE PUBLICITY THAT WOULD GET!!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...