Jump to content
SAU Community

Recommended Posts

there has been a bit of info posted about remaps and aftermarket computers. i was initially going to setout and get a pfc and a tune done as i only wanted to stretch the limits of my turbo without going too overboard. i dont track my car or drag it. its just a daily driver and in the last 2 years of ownership i have travelled less than 10,000 kms (yeh everything i do is really close to my home).

Car

1998 R33 gts-t 40th anniversary

mods:

walbro 550hp fuel pump

JJR coil packs

turbo back exhaust with high flow cat, dump, apexi n1 muffler

Greddy profec spec b electronic boost controller (12.5 psi)

Blitz pod filter with cold air snorkel and heat sheild

monza front mount intercooler

Toshi remap

had the remap done today. took about 5 hours all up. after leaving toshi's house i took the car for a spin on my own. and damn. the thing literally lifts off. i never dynod my car before hand i kind of wish i had now. but it couldntve been anymore than 185kw and running average. flat spots. when you compare before and after its like my car was being held back from releasing all this potential. and it wasnt much to get that potential. revs out a lot quicker, power everywhere. lots more torque. no more flat spots in any gear. my boost was holding stable at around 11psi before the remap and now on the profec b it holds stable at about 12.6 psi (8.6 for all you profec b owners and my settings are set 52, gain 20, set gain 27) the car now has its boost limiter gone, speed limiter gone, rev limiter gone just feels free to do whats its wanted to do for the last 2 years.

some guys on these forums have dyno'd after the remap with 10psi making nearly 200kw at the wheels. my car easily makes over 200 now. but feels like it too and the torque feels a lot higher too. toshi doesnt think the turbo will make anymore power at all though as the afm is maxed out.

but bang for buck best performance mod you can get for your line and for a street only car it is more than enough power to make me smile.

Edited by DrewII
Link to comment
https://www.sau.com.au/forums/topic/245037-just-finished-getting-a-toshi-remap/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

good results, no one here doubts the ability of a remap

will certainly make power and perform quiet well

it has no resale value and if you make changes to your car, you have to typically pay the full price again

good results, no one here doubts the ability of a remap

will certainly make power and perform quiet well

it has no resale value and if you make changes to your car, you have to typically pay the full price again

this is very true

however

power fc + tune = 1500-2000

if you want to retune a modification pay another = 3-500 so all up about 2,500 (cheaper of course if tune yourself)

toshi remap = 500

if you want to retune modification pay another 500 so all up 1000. still works out way cheaper than aftermarket computer. even if tune a third mod still cheaper.

and the 16x16 map computers are good enough for street tuning. toshi tuned a R33 few weeks ago with an HKS turbo he said the guy dyno'd it after and the car made 360 horse power. so the power capabilities are also there. he did say if you are looking for numbers of 400hp or more he would recommend the power fc or alike. the road tune really did simulate a proper dyno tune as well. we went on the highway up towards Gosford and gave it a good run with a mix of red lining and speed/gear variations. for a very short period of time this was the only danger of the road tune however there were no cars around at all.

Edited by DrewII

The person doing my remaps only charges about $150 for touch up tunes, he stores all his customers tunes on his laptop so he's not starting from scratch again and therefore charges stuff all; most of the tuners that do remapping I know of are the same. Last time I had a touch up (setting up cam gears) the car was on the dyno for more 5 hours and I was only charged $100

The person doing my remaps only charges about $150 for touch up tunes, he stores all his customers tunes on his laptop so he's not starting from scratch again and therefore charges stuff all; most of the tuners that do remapping I know of are the same. Last time I had a touch up (setting up cam gears) the car was on the dyno for more 5 hours and I was only charged $100

shit thats cheap.

Good result, the re-maps are only good when tuned live IMO.

Sounds exactly the result it should be. The letdown with those kind of remaps is when they are done offsite (posted in the mail etc).

I had a remap years ago, one of the first... was good value.

Although, stock turbo legitimately over 200rwkw? i don't think so :D

Good result, the re-maps are only good when tuned live IMO.

Sounds exactly the result it should be. The letdown with those kind of remaps is when they are done offsite (posted in the mail etc).

I had a remap years ago, one of the first... was good value.

Although, stock turbo legitimately over 200rwkw? i don't think so :P

lol i know what you mean by that. and yeh run the boost run the risk.

and about blowing the engine? it wouldnt be any unsafer for your engine than getting a tune on a dyno. as i said it simulated a proper dyno tune. tested for pinging at extremely high revs. i was surprised my turbo didnt blow during the tune because i thought here we go now going to have to upgrade after todays tune. but honestly i gave this turbo an absolute pounding in the #$$ for a few hours and the turbo ran sweet. easily the biggest pounding iv ever given my turbo. lucky it survived? maybe.

with regards to him going to melbourne you would have to ask him yourself. hes a member on these forums. he has sent numerous remaps all over the country i have spoken to a couple of people on these forums who received one in the mail who were all extremely happy with the results. one guy in perth was ranting about it too.

Neither do I..

Glad you're happy with the results though.

Siddr20 made 196 kw on a dyno at 10psi with manual boost tee, side mount intercooler and Toshi remap. i think an extra 4kw is easily achievable with a big front mount 12.5 psi holding very steady with profec spec b. results like this are also in the RB25 dyno thread. a dyno run will tell though.

Edited by DrewII
Although, stock turbo legitimately over 200rwkw? i don't think so :P

i'm surprised that you'd share this outdated view. its been flogged to death on here.

countless 33's are making over 200rwkw on stock turbo.

12psi - exhaust - tune - cooler. fairly simple formula. its nothing special as far as i can tell.

^^ and not one has ~109mph to back it up now have they? So my outdated view suddenly looks realistic again.

Until enough people run ~109mph passes on the stock turbo unassisted, i'll believe it can push that much power.

To date, i dont think we've had one person do it unassisted. Most are still stuck around the 104-105 mark which is 190-200rwkw give/take

^^ and not one has ~109mph to back it up now have they? So my outdated view suddenly looks realistic again.

Until enough people run ~109mph passes on the stock turbo unassisted, i'll believe it can push that much power.

To date, i dont think we've had one person do it unassisted. Most are still stuck around the 104-105 mark which is 190-200rwkw give/take

i think most people with stock turbos are just that. running high boost without a tune not performing like it should. like i said my car feels like its been opened up again to its full potential like it was being held back for the last two years.

could also be that people with over 200wkw havent dragged their cars and the majority that have dragged are actually making ~190 like you said hence why you probably havent seen many.

but hey we can all say what we want. in the end cold hard proof is the only way to truly tell.

^^ and not one has ~109mph to back it up now have they? So my outdated view suddenly looks realistic again.

Until enough people run ~109mph passes on the stock turbo unassisted, i'll believe it can push that much power.

To date, i dont think we've had one person do it unassisted. Most are still stuck around the 104-105 mark which is 190-200rwkw give/take

so rb20's will just make 200rwkw with rb25 turbos but rb25's wont?!?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day  
    • While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
    • Are you 100% sure this isn't tune related?
    • 140-150 across the board. At this point hoping the grounding harness fixes it. My grounds are all tied to the chassis and none to the battery. For SR and KA that’s never been a problem for me but had a few other guys here and Reddit who told me RB really like a very solid ground setup tied to the battery so going to try that next, I’m stumped if that doesn’t do it. Never had a car have spark and fuel and not fire off before. Only thing I can think is the spark is intermittent/weak because of grounds nothing else really makes sense at this point 
    • I am having close to the same issue. Can you help me with what wire you grounded to get your pump to trigger?
×
×
  • Create New...