Jump to content
SAU Community

Recommended Posts

Hey, i'm on my P plates so i don't want my car decked out with a heap of mods. I just want to know whats the best part to put in my car to make it go faster. I want the best results though, i don't want a part thats not going to do barely anything. I want to be able to notice the improvement in power.

My friend had a Celica that at like 4,000 rpm's in 3rd gear it just seemed to boost forward a fair bit and he said it did the same in 5th gear. He said it had to do with the fuel injectors but he knows nothing about cars so 99% chance hes probably wrong. His was non turbo etc so yeah if theres a part that can make that happen then i want it lol.

So far i just have an exhaust system.

Also please don't spam my thread with "your on your Ps, you aren't allowed modifications" or "your not a skilled enough driver, just get handling mods like braking and suspension". I know a ton of people on the forum that have illegal mods, so by me modding my car its no different to everyone else with their illegal mods. Also i'm not going to be a dickhead in it so i don't need handling etc, i just want a bit more power.

I reckon the only single part that would mean instant gains would be a turbo, so thats out of the picture aye..

Like me your on your P's.. so i guess the only way your gonna' get noticable gains is with a few mods that compliment each other.

Pod Filter, enclosed..

Cold air intake.

Exhaust ( you already have one, but how big is it ? )

If you want more information dude, theres a sticky by EUG that goes into great detail, you just pick and choose what mods you want..

and just in case you want a lil sneak peak heres a lil peice from his write up..

" How to get more power from a naturally aspirated engine?

There are many ways to get more power; it all comes down to budget and application.

Power is defined by the rate at which work is performed over a unit of time. Used in our context, power will represent the maximum kilowatts (kW) a vehicle produces as measured on the dyno. However, the key factor in the above equation to take into consideration here is 'time', which is essential for 'response'.

Being a naturally aspirated, the motor is neither turbocharged nor supercharged. This means that the motor relies on vacuum created by the cylinders and natural atmospheric pressures to draw in ambient air for combustion.

In order to get more power you will have to rely on the basic principal of: letting the motor breath/work better, so to speak. This is done by removing the restrictions within the system and thus creating more efficiency.

Here is a basic list of what can be done, we shall elaborate on them at a later stage:

Intake (pod filter, panel filter, larger throttle body, cold air feed)

Neat Cold Air Intake

Professional Looking Heatshield

Exhaust (extractors, cat converter, cat back exhaust) "

Head over here .

http://www.skylinesaustralia.com/forums/Po...sp-t194033.html

Have fun man!

MRXTCZ

thanks for the reference vik.

have a good read of that thread tyson. there is no ONE PART to enhance performance.

handling mods will make you go faster, it just seems like you are chasing a number.

i'll be keeping an eye on this thread.

I think the most important question you should be asking yourself is "how much am I prepared to spend?"

In terms of an NA car you need to spend some money to net a half decent gain.

You need to focus how well the air flows in and out of an NA engine.

The best gains to to be had are in cams. Have a look around the net for a set of aftermarket camshafts ($600 odd new). To get the best gains you'll also need a pair of adjustable cam gears for both the inlet and exhaust camshaft ($300 odd a pair new). Do you have a S1 or S2 R33? I can't tell from the pic. Because whether or not you have an NVCS will also influence cam gear choices. The final item to tie it all together and tune the engine is some form of engine management. Now, personally I cannot justify an entirely new ECU system for the 20-25odd KW gain your going to be getting. A simple Apexi SAFC to tune and set the engines increased demand for fuel will suit without a problem. Once all this is done, an upgrade in fuel pump is proprably a good idea too as the demans placed up the OEM pump are significantly increased and the unit is probably getting warn down after 15odd years of use and abuse - DET is cheap, easily found and is more than enough for your application. If you get this far, have a chat to your tuner as the injectors may be starting to struggle at this point too. $100 odd and you got yourself a set of second had RB25DET injectors. Cheap upgrade.

Its a relatively cheap set of modifications you can perform to gain a half decent power figure. Even with jsut 125kw your increasing engine performance by 25% which is a fair whack.

Its a place to start. From here on in things get expensive. Your looking at taking the head off, porting, polishing, increasing engine CC's, compression ratio's etc. and its bloody expensive.

Also i'm not going to be a dickhead in it so i don't need handling

It's a shame my sig is currently full of comedy gold. If it wasn't, this would have just made it.

If you wanted power without control, you should have bought a Falcodore. There's a modification for you.

Edited by scathing

i agree with Alan (scathing) that has to be up there with the stupidest comments i've ever heard.

if you want to go fast legally, improve your driver skill. i can match some gtst (and a few gtr) times around QR with purely suspension work and a bit of practice.

typical 17yr old? gives the rest of us a bad name. The power leads to handling problems, yea you might not plan on being a dickhead all the time, but what about the occasional time?

And didnt Hot4s shave a couple second off their track time in the Evo with just a wheel upgrade?

Anyway off topic, depending on how much money you have will depend on the power upgrade. NA motors are a system, to get the best out of it, the whole system needs to be upgraded. Exhaust, Cams, Injectors, etc, you will feel and hear a change for a while, but soon after, you will get used to it and want more. Keep that in mind Champ.

If i were to mod my NA there would only be a few things i would consider doing to my engine. That would be a full exhaust and a decent CAI. Anything more and you will be spending a lot of cash for little gain.

IMO if its accelaration you are after you are better off looking into other areas of your car. I would be changing my diff gears to the possible shortest ratio (I believe gts4 diffs are shorter than the rest) And using tyres of the smallest rolling diameter that you are legally allowed to run...

"I know a ton of people on the forum that have illegal mods, so by me modding my car its no different to everyone else with their illegal mods. Also i'm not going to be a dickhead in it so i don't need handling etc, i just want a bit more power"

keep up with that attitude my friend and you'll mod yerself right round the nearest tree and into the hospital.

I am from the good ole uk, so know very little of the legalities of the modding situation over there. modifing an NA (and keeping it na) isnt a one part fits all scenario..so have a shop around.

lightened flywheel - you will notice some difference

Shave the head a few thou to bump up the comp a little will help also

lower diff ratio has always been my favourite mod for gains

Cold air/ RAM air intake

Anything more than this and you start talking big work and big $

I would have recommended a bolt on Supercharger ( VT Commodore EAton M90 ) but that will need tune and many other mods so still wouldnt be cost efficient compared to a whole turbo motor swap

other than that a tune maybe ?

ok as every ones being saying exhasut, CAI, cams,.

ill give you my sotry.

R31 skyline RB30E

started with 70RWKW with only a 2.25' exhaust

after nistune ecu, custom crow cam, exstractors, k&n pod. all tuned i had 118.6RWKW.

cost of about $3500 due to getting some parts cheeper.

www.nistune.com to find out more only cost $250

I think the most important question you should be asking yourself is "how much am I prepared to spend?"

In terms of an NA car you need to spend some money to net a half decent gain.

You need to focus how well the air flows in and out of an NA engine.

The best gains to to be had are in cams. Have a look around the net for a set of aftermarket camshafts ($600 odd new). To get the best gains you'll also need a pair of adjustable cam gears for both the inlet and exhaust camshaft ($300 odd a pair new). Do you have a S1 or S2 R33? I can't tell from the pic. Because whether or not you have an NVCS will also influence cam gear choices. The final item to tie it all together and tune the engine is some form of engine management. Now, personally I cannot justify an entirely new ECU system for the 20-25odd KW gain your going to be getting. A simple Apexi SAFC to tune and set the engines increased demand for fuel will suit without a problem. Once all this is done, an upgrade in fuel pump is proprably a good idea too as the demans placed up the OEM pump are significantly increased and the unit is probably getting warn down after 15odd years of use and abuse - DET is cheap, easily found and is more than enough for your application. If you get this far, have a chat to your tuner as the injectors may be starting to struggle at this point too. $100 odd and you got yourself a set of second had RB25DET injectors. Cheap upgrade.

Its a relatively cheap set of modifications you can perform to gain a half decent power figure. Even with jsut 125kw your increasing engine performance by 25% which is a fair whack.

Its a place to start. From here on in things get expensive. Your looking at taking the head off, porting, polishing, increasing engine CC's, compression ratio's etc. and its bloody expensive.

Thanks, i don't really want to be spending a whole lot on my car since i mainly only want it till i'm on my opens or a year or two after so that i can then buy a turbo, hopefully a R34 GTR. What's an Apexi SAFC tune and how much does that cost? Also i think i see injectors being sold a fair bit on this site, you need like a set of 6 or something don't you? I always look at the parts for sale to try to learn more about what does what. Also what is a DET?

Thanks for all that, that doesn't look too expensive which is good. Oh and i have a Series 1 R33.

If i were to mod my NA there would only be a few things i would consider doing to my engine. That would be a full exhaust and a decent CAI. Anything more and you will be spending a lot of cash for little gain.

IMO if its accelaration you are after you are better off looking into other areas of your car. I would be changing my diff gears to the possible shortest ratio (I believe gts4 diffs are shorter than the rest) And using tyres of the smallest rolling diameter that you are legally allowed to run...

Thanks, whats a CAI? Also how would i change my diff gears and would making them shorter have any negative effects?

I've read the sticky regarding performance but didn't really understand everything thats all.

To all those saying i sound like a dickhead etc, i've already got good handling. I don't go fast around corners, i don't take my car to the track or anything. The only reason i want more power is just for accelerating basicly in a straight line. I'm not wanting more power so i can get out of corners real quick or anything since yeah that'd be stupid. Going in a straight line doesn't require the best of the best handling.

Thanks, whats a CAI? Also how would i change my diff gears and would making them shorter have any negative effects?

CAI = Cold air induction

The only negative affect you get from putting in shorter diff gears is that you car sits on a higher rpm at any given speed. It will really only make a difference to fuel economy if you spend a lot of time on the highway.

And it will only be worse on fuel on the highway. from my experience dropping diff ratios actually improved economy in normal stop start driving conditions. There are a lot of wives tales about dropping diff ratios usually told by know it all old guys... Crap such as " It will get off the mark faster but its got no top end acceleration " Well from my experience thats crap....You will feel gains at every speed.

As for having no top end ? I found that I had a lot more top end acceleration.I wouldnt worry too much about it revving harder as you got an overdrive gear already.. If it only revved 500 rpm harder on the freeway for the same given speed then thats quite acceptable. But the difference in acceleration you would be much happier with.. Go to a diff specialist and see what they quote you. Dont let some hack mechanic do it as if its not set up correctly you will have the annoying howl coming from it...not good

Also what is a DET?

DET is short for the RB25DET, which is what GTSts have. basically, you have a DE, non turbo, hence T stands for turbo :P

D= Dual Overhead Cams

E= EFI (Electronic Fuel Injection)

T= Turbo

and for the record, i think handling mods, even cheap ones like sway bars and strut braces, are a good investment no matter what power levels you have

Edited by G0DZLR

If your not planning to have it that long then I wouldnt even recommend doing too much to it.

instead of spending bout $1000-$1300 on cams and gears, use that on your next turbo car..(I picked these mods because u already have a full exhaust they are the next best thing to do for power)

also... people are probably going to have mixed opinions about what I say next, but I have read this in a few magazines about skylines....

went something along the lines of:

"Skylines are a supurb car to drive for performance and handling, however there are quicker cars that go in a straight line, but they are one of the toughest competitors around a track."

Not saying obveously you can make them go faster in a straight line, but it takes mods and money to do so... stuff that at the moment I imagine arent flying at you(im a p plater too)...

so definetly do try a cold air intake and a heatsheild, but you'll be spending a decent amount of money to notice any type of gains from an n/a...

one final thing... personally, I would recommend doing cam gears for now, I did it to my car last week and noticed a heap of difference in response and torque, which from the sounds of it, you are after aswell.

Adam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, after the full circus this week (new gearbag, 14 psi actuator on, injectors and AFM upgraded, and.....turbo repair) the diagnosis on the wastegate is in. It was broken. It was broken in a really strange way. The weld that holds the lever arm onto the wastegate flapper shaft broke. Broke completely, but broke in such a way that it could go back together in the "correct" position, or it could rearrange itself somewhere else along the fracture plane and sit with the flapper not parallel to the lever. So, who knows how and when exactly what happened? No-one will ever know. Was it broken like this the first time it spat the circlip and wedged itself deep into the dump? Or was it only broken when I tried to pry it back into place? (I didn't try that hard, but who knows?). Or did it break first? Or did it break between the first and second event of wierdness? Meh. It doesn't matter now. It is welded back together. And it is now held closed by a 14 psi actuator, so...the car has been tuned with the supporting mods (and the order of operations there is that the supporting mods and dyno needed to be able to be done first before adding boost, because it was pinging on <<14 psi with the new turbo with only a 6 psi actuator). And then tuned up a bit, and with the boost controller turned off throughout that process. So it was only running WG pressure and so only hit about 15-16 psi. The turbo is still ever so slightly lazier than might be preferred - like it is still a bit on the big side for the engine. I haven't tested it on the road properly in any way - just driven it around in traffic for a half hour or so. But it is like chalk and cheese compared to what it was. Between dyno numbers and driving feedback: It makes 100 kW at 3k rpm, which is OK, could be better. That's stock 2JZ territory, or RB20 with G series 550. It actually starts building boost from 2k, which is certainly better than it did recently (with all the WG flapper bullshit). Although it's hard to remember what it was like prior to all that - it certainly seems much, much better. And that makes sense, given the WG was probably starting to blow open at anything above about 3 psi anyway (with the 6 psi actuator). It doesn't really get to "full boost" (say 16 psi) until >>4k rpm. I am hopeful that this is a feature of the lack of boost controller keeping boost pressure off the actuator, because it was turned off for the dyno and off for the drives afterward. There's more to be found here, I'm sure. It made 230 rwkW at not a lot more than 6k and held it to over 7k, so there seems to be plenty of potential to get it up to 250-260rwkW with 18 psi or so, which would be a decent effort, considering the stock sized turbo inlet pipework and AFM, and the return flow cooler. According to Tao, those things should definitely put a bit of a limit on it by that sort of number. I must stress that I have not opened the throttle 100% on the road yet - well, at least not 100% and allowed it to wind all the way up. It'll have to wait until some reasonable opportunity. I'm quite looking forward to that - it feels massively better than it has in a loooong time. It's back to its old self, plus about 20% extra powers over the best it ever did before. I'm going to get the boost controller set up to maximise spool and settle at no more than ~17 psi (for now) and then go back on the dyno to see what we can squeeze out of it. There is other interesting news too. I put together a replacement tube to fit the R35 AFM in the stock location. This is the first time the tuner has worked with one, because anyone else he has tuned for has gone from Z32 territory to aftermarket ECU. No-one has ever wanted to stay Nistuned and do what I've done. Anyway, his feedback is that the R35 AFM is super super super responsive. Tiny little changes in throttle position or load turn up immediately as a cell change on the maps. Way, way more responsive than any of the old skool AFMs. Makes it quite diffifult to tune as you have to stay right on top of that so you don't wander off the cell you wanted to tune. But it certainly seems to help with real world throttle response. That's hard to separate from all the other things that changed, but the "pedal feel" is certainly crisp.
    • I'm a bit confused by this post, so I'll address the bit I understand lol.  Use an air compressor and blow away the guide coat sanding residue. All the better if you have a moisture trap for your compressor. You'd want to do this a few times as you sand the area, you wouldn't for example sand the entire area till you think its perfect and then 'confirm' that is it by blowing away the guide coat residue.  Sand the area, blow away the guide coat residue, inspect the panel, back to sanding... rinse and repeat. 
    • The detail level is about right for the money they charge for the full kit... AU$21.00 each issue, 110 issues for a total of $2,300 (I mentioned $2.2K in the first post when the exchange rate was better). $20/week is doable... 馃槓
    • If planning on joining us for the day(s) please indicate by filling in this form. https://forms.gle/Ma8Nn4DzYVA8uDHg7
  • Create New...