Jump to content
SAU Community

Gt35r Vs Garrett T04z - Discussion (just Post In This Thread To Create A Database)


Recommended Posts

My tuner (Ant Scali) has only just returned from Mt Buller.

He was working with Steve on the r35 development.

My car WILL be tuned Friday arvo.... then I will post up results as soon as possible.

26 with .84 T04Z

13065_226473479702_508809702_4240776_6507335_n.jpg

20 psi with little timing.

Just picked up the car, were doing some more mapping tonight. 4th gear pulls.

Doesn't feel to bad, mind you I have yet to have a proper drive of it.. Everytime I try to make a rationed opinion the adrenaline kicks in and I forget to keep an eye on how responsive it is.. lol..

Fix that boost control :D

If you can get it to pull to 21psi much sooner it'll be interesting to see what happens before/after.

So yes... that means get the graphs overlapped when you do :)

Funnily enough, almost a carbon copy of the one just above.

On a preliminary tune, it went 540rwhp (~400rwkw) at 19psi. Quite a bit lazier than the 35R though. On the same dyno, the 35R went 510rwhp on 26psi.

Am changing boost controller (as we weren't impressed with it's ability to hold boost) and tuning for 25psi next week. When that's done we'll print out a graph overlapping the 35R run with the T04Z run and I'll post it up.

Edited by Brockas

Sweet, sounds good, what boost controller did u have in it.

ya didnt think the Z could defy human nature with response. but will be interesting to see the true outcome and how fare apart they are.

Edited by nigel

Yeh at this stage it looks like it's going to be about 500rpm difference, but I believe the area under the curve will be greater with the Z.

I had a Greddy Profec B II, and I've just ordered a Blitz Dual SBC Spec-R.

Nar, overlapped Scatalotto's. His tromped mine everywhere, but we'll see how it goes with the new boost controller and some cam timing adjustments.

26 with .84 T04Z

13065_226473479702_508809702_4240776_6507335_n.jpg

20 psi with little timing.

Just picked up the car, were doing some more mapping tonight. 4th gear pulls.

Doesn't feel to bad, mind you I have yet to have a proper drive of it.. Everytime I try to make a rationed opinion the adrenaline kicks in and I forget to keep an eye on how responsive it is.. lol..

Did Paul tune your car? Is that the Twin scroll or just a single entry? Have to let me know how responsive it is etc

I've had fairly good results using the GT35...

Thinking of going to a GT37 or GT40 when i do a 3L bottom end...

car wasn't running it's best on the day of the dyno either...

post-27540-1261453111_thumb.jpg

Ok, mine went 580rwhp today.

Will pick it up and scan dyno sheet tomorrow.

Keen to see a comparison vs your gt35.

what boost to make 580rwhp?

How much longer (RPM) to reach full boost than gt35?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
    • Yeah. OK. I'll say the same thing I say to everyone. You do not have to use 100% throttle all the time.
×
×
  • Create New...