Jump to content
SAU Community

Recommended Posts

  • Replies 138
  • Created
  • Last Reply

Top Posters In This Topic

got afew cars on the go. 82 datsun 720 kingcab getting shaved etc, ED falcon shitbox (currently on $150 19s not the 17s in the pic)i converted to manual, fitted an LSD and i got the head off atm doing a port job and upping the compression. the stagea which i have coilover and R34 brakes to fit soon (disgustingly high with 18s) then theres the beast. my 1968 VW squareback

P9120399.jpg

181628_493662736115_533251115_6499452_557151_n.jpg

P1030154.jpg

155702_459185286115_533251115_5981121_4949296_n.jpg

P1010061.jpg

P1010062.jpg

P1010073.jpg

James, that's a sick buggy! I've been thinking about getting my electric one up and running again....just gotta replace the seals and oil in the rear shockies and replace/repair the munted cells in the battery packs

so you're handy with VW motors then?

my dad and i have a off road buggy. basically a 67? dub with shell and floor pan gone with rollcage in place. got a fastback on the way for the motor (1600) and rear suspension set up.

how hard is it to make it carby and do you have and tips on modding for power. we're in a comp with my uncle and i want to smash him lol

his is a bit.... crap. but its running a datto 200b motor with twin SU's. Note my awesome helmet/goggles

P4290050.jpg

yeh very handy. i got a 72 fastback too, thats locked away in my dads mates garage til i got a garage build (8 months ago hahahHAHAHA jokes on him). most fastbacks are dual carby and its rare to see a bosch fuel injection system still installed and running. use the type3 trans too they are abit stronger than a beetle one and have better ratios. might be worth using the pancake engine with dual carbs so if you snap a fan belt you dont cook the engine

basically bigg headers, big exhaust and the right amount of advance is the best increase without massive coin. on my old beetle i very lightly ported and cleaned up the intake port and then the same with the exhuast ports but polished the hell outta it to near mirror finish and the rest was bog stock apart from a 009 dizzy and a good tune and she flew!

I NO NAHSING!!!

the type3 rear suspension (if its an IRD model and not swing axle) is more beefed up from the beetle too, there 2 rear spring plates (trailing arms) instead of one so there less camber change though its range of motion. also the drum brakes are bigger

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...