Jump to content
SAU Community

Recommended Posts

ok, as I said I don't push my car hard on road, I drive carefully and slowly in wet. Maybe it got something to do with the suspension, the Buddyclub N+ has a quite stiff spring rates, front 10, rear 8.

ouch at that pickup truck pic.

I know where your coming from and its not really your driving style like others have pointed out. Its your setup, thats all. Stiff suss wont see you going sideways unpredictably at really low k's but it is one of many factors, your camber, your tyre, and the amount of surface contact. get em all sorted out and you should have no drama other than your right foot. I addressed these issues and the problems gone away and I'm still running my stiff tiens.

  GTS4WD said:
next time it happens, just stick your hand out the window and yell out

"DDDDDDDOOOOOOOOORRRRRRRRRIIIIIIIIFFFFFFFFTTTTTTTTOOOOOOOO!!!!!!"

KOOOMANNNGIII ATTACKKKKK!

srsly tho, i run the same tryes (dunlop lemans lm702 245/40/18) and with 5/7 coils, struts, sways, castor, camber, hicas lock and 265rwkw i'm fine...

it's ALL in the driving, not the car

  carbon S said:
ok, as I said I don't push my car hard on road, I drive carefully and slowly in wet.

Ahem

  carbon S said:
the car starts to "Drift"....sometimes in a hurry right turn

Thanks for coming.

I've driven a modified 5.0L Commodore SS auto with Goodyear F1s on the front and retreads on the back in the wet, and managed to not spin out. I can guarantee that car would have less wet weather rear grip, and a shedload more torque that is a lot less predictable in its delivery.

  joeyjoejoejuniorshabadoo said:
srsly tho, i run the same tryes (dunlop lemans lm702 245/40/18) and with 5/7 coils, struts, sways, castor, camber, hicas lock and 265rwkw i'm fine...

it's ALL in the driving, not the car

I don't have the castor, camber kits, I will get the camber kits see if make a different, if it still does the same thing, then i must be a bad driver

  • 2 weeks later...

Coilovers are a contributor to this, i also had to much camber as i was running 18x10's with a big ofset, granted it was very fun coz all i had to do was turn the wheel in the wet and it would slide out nicely no matter what tyres i had on there... also having a light tuned RB26 mad the slides last :P its just a fact of life with these sorts of cars especially with coilovers +to much camber. its no fun to just putt around doing 20 in the rain so let it slide and just enjoy the ride

Its in the right foot......plenty of people drive around with this sort of HP at the rears only ( My VU ( ss ute ) is 700hp and over 1000nm rear wheel drive and not much weight in the back without the spare etc.... was a brilliant car to learn propper throttle control especially in the wet biggest issues where making a turn out of a side street uphill in the wet the rears would just spin and spin and it was almost impossible to get traction but after some proper practice and some forced self control....... it drives fine.

Tuning and changing your suspension may well help but learn to control what you have got appropriately first....

:(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...