Jump to content
SAU Community

Recommended Posts

Hi everybody wrecking an r33 s2 silver automatic trying to get rid of as much as i can as im moving out next saturday so if your interested let me know otherwise car will just be going to the wreckers.

Off the top of my head

Full set of 9 skyline mats $80

All 3 rear seatbelts and buckles $35

Skyline Runners (silver part that is on your door runner) $25

AFM Pink Sticker $30

Standard Rear Bumper Silver Damaged ding in the rh side $20 (pickup only)

Standard ECU $25

Rear Boot Struts & Wiper $45

Boot Bracket $20

Rear Wiring loom (brake lights, tail lights, antenna, license plate lights) $75

RH Side Front Guard White scrathed all over same condition i recieved from alljap paid $120 sell $50

Door Trim $100 pair or complete doors sold $300 pair pickup only if buying whole doors

Jack and Kit $30

Snorkle X2 R33 & R34 $15 each

Pipe running from AFM to engine $30

Mud Guards from front of car connecting piece from guard to top of tyre well not for front $25

Skyline Garnish from between taillights $30

Plastic console from under steering wheel can sell as whole or pull air con vents off hazard light button and clock up to buyer piece is cracked as shown in photo $30

Hicas unit Lsd dont know wat to call it there is a photo of it shown $30

Pair of Blue and white GT badges for front guards $45

Autotechnica car cover full length size clips and straps for underneath the car paid $250 has some cat scratches on rear and bit dirty sell $75

R33 Airbox without filter $20

There are also some attached photos of the engine and centre console if anybody see's anything they like all photos of items attached let me know if your interested if you think the price is ridiculous pm and we'll work something out. Need all parts gone asap so dont hesitate to ask. All parts are plus postage unless stated

Cheers, Mitchell

post-36053-1228461383_thumb.jpg

post-36053-1228461489_thumb.jpg

post-36053-1228461717_thumb.jpg

post-36053-1228461785_thumb.jpg

post-36053-1228461882_thumb.jpg

post-36053-1228461952_thumb.jpg

post-36053-1228462075_thumb.jpg

post-36053-1228462154_thumb.jpg

post-36053-1228462219_thumb.jpg

post-36053-1228462368_thumb.jpg

post-36053-1228462449_thumb.jpg

post-36053-1228462538_thumb.jpg

post-36053-1228462603_thumb.jpg

post-36053-1228462656_thumb.jpg

post-36053-1228462713_thumb.jpg

post-36053-1228462799_thumb.jpg

post-36053-1228462843_thumb.jpg

post-36053-1228462920_thumb.jpg

post-36053-1228462955_thumb.jpg

post-36053-1228462988_thumb.jpg

post-36053-1228463006_thumb.jpg

post-36053-1228463020_thumb.jpg

post-36053-1228463053_thumb.jpg

post-36053-1228463084_thumb.jpg

post-36053-1228463118_thumb.jpg

post-36053-1228463162_thumb.jpg

post-36053-1228463201_thumb.jpg

post-36053-1228463300_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/247795-r33-s2-silver-wrecking-all-parts/
Share on other sites

SirSkyline : have both headlights but not really in condition to be reused if you want photos pm me and ill get onto it for you

Thanks anyways mate. I need a good one because i have cracked in the lens in mine and I cant stand it anymore

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...