Jump to content
SAU Community

Recommended Posts

Thought I'd take some pictures of taking off my front bumper and make a Tutorial so its easier for other people to give it a shot. so here we go.

1.) Get a flat head screw driver, poke it into the gap of the front indicator (where arrow shows) and pop out the indicator.

1.jpg

2.) There are 5 plastic screws where the grill is, which are easy as popping them up and pulling them out.

2.jpg

3.) 2 screws that hold the body kit onto the fender, one is right at the edge of the bumper, and the other is in the middle which is kind of hard to get too, needa squeeze your hand under or through the cover to get too it.

3.jpg

4.) After those are done, you'd need to push the edges of the front bumper down to clear the little clip that holds in in the middle (Circled in blue).

4.jpg

5.) your bumper should slip off easy and look like picture under. (to fit back on just reverse the process)

End.jpg

After doing all this, looking at installing a fmic never looked any easier :D

Thanks for your time.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/248385-taking-off-gtt-r34-front-bumper/
Share on other sites

Just one thing that I did differently when I took our off was I took the indicator light/globe out of the holder from behind instead of putting a screw driver near the paint. (showen in step 1.)

You can the leave the whole holder assembly in the bar and then remove it if needed when the bar is off the car it is much easier and you should then avoid all possibilty of any paint damage.

You will also need to remove about a dozen bolts underneath the bar as well that hold the drip tray on and the inner gaurds on.

Other than that great write up

Edited by bigafoot
  • 2 weeks later...
  • 5 months later...
  • 1 month later...
  • 3 weeks later...
  • 3 months later...
  • 2 weeks later...
  • 3 weeks later...
  • 1 month later...

"...the other is in the middle which is kind of hard to get too, needa squeeze your hand under or through the cover to get too it."

Man I am having serious trouble getting my hand (with spanner attached) to that screw. I'm just ripping my arm to shreds. Any special tips on an easy way to do it without losing too much blood?

  • 1 month later...
"...the other is in the middle which is kind of hard to get too, needa squeeze your hand under or through the cover to get too it."

Man I am having serious trouble getting my hand (with spanner attached) to that screw. I'm just ripping my arm to shreds. Any special tips on an easy way to do it without losing too much blood?

Sorry about the late reply, I am hardly on the forums now due to selling my skylines awhile ago..

but to your question, you could take the cover off (Plastic surrounds around the front wheel) there's only couple plastic screws holding it in, 2 on the bottom and 2 in the guards from memory, as soon as you take that off getting to that middle screw will be and ease and you wont have to squeeze in, this takes longer to take off the front bumper and more things to put back on.

  • 1 month later...
  • 4 months later...

My inner plastic guard is basically stopping me from getting to the screws holding the front bar on near the tyres.

I can' t even get a finger through let alone a screw driver. Any tips for 34 GTR or is it different to GTT as far as removal technique?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...