Jump to content
SAU Community

Recommended Posts

True and agree Dane, I just meant the lack of manufacturer variety isn't a deal breaker for me.

Me either, still the best form of motorsport by a long shot going around imo!

yeh right on phunk.. bring back the SWRT cars from the early 2000-2006.. they are hwat...

You're not wrong!

swrtsweden2.jpg

Pity the 06 was a bit of a dog...

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Agreed that WRC USED TO BE the best motorsport around. I was involved in rallying for a while, ran an AE86 Trueno notchback. Wicked fast and fun, but rally is all but dead. It's getting harder and harder to get approval to run events, and more teams keep pulling out on many different levels. It's sad to say, but in Australia at least, rally won't be around much longer. And if lower level rally dies, you can bet they won't see reason to fund WRC events. That's why I've been building up a Superlap car, was going to build a rally car but couldn't justify the outlay for maybe a season or two of use.

^^^ And this is why so many clubs are struggling, particularly old school clubs like mine (BSCC who host the APRC in Qld) who have failed to see the writing on the wall for gravel events. Their efforts would be much better spent on focussing on tarmac events where the interest and money seems to be now.

its just because australia is such a large country... with a small and young population.. it takes hours and hours to get anywhere from anywhere else.. and as is the australian way... half of us just CBF'd

its a viscious cycle, and the same cycle that everyone and everything is in.... without public support, events wont get big attractions... but without big attractions, events wont get public support...

^^^ And this is why so many clubs are struggling, particularly old school clubs like mine (BSCC who host the APRC in Qld) who have failed to see the writing on the wall for gravel events. Their efforts would be much better spent on focussing on tarmac events where the interest and money seems to be now.

Sorry Benny but can't agree with that at all. I'm sure Timmy well tell you stories from last weekend's first round of the TRS. 25 entries, biggest field in Tassie rallying for a while. ARC is a bit of a joke sure but to say gravel rallying has no future is just absurd. There are still plenty of people out there willing to support gravel rallying, it will only die if people take an attitude like "oh it's got no future, may as well give up". Tarmac rallying is going through a purple patch at the moment, but that's because it is still relatively new and exciting. Personally I think we need both and the person that wins in both disciplines will probably be the best driver in Australia.

As for the WRC thing, next year's Citroen challenger. I feared the next-gen cars may be a bit pedestrian, but they don't look much slower to me.

the ARC in general couldnt get anymore boring if they tried. ( the only one having fun are those in the car) the cars are faster in the carpark.

and please dont take this the wrong way as not a shot at you , but 25 entries being a big field is a bit of a worry.

i remember going to state rallies in the early nineties when group A (no restrictors) were allowed ( and group g before that! :P ) with fields of 60 plus cars.

for a rally to be worth it because of the effort to close the roads , volunteers etc you need large fields! just my opinion though.

Sorry Scott, but a field of 25 is pus. You must becyoung, as giant and I both recall, 70 plus is where it's at. As it stands now, no sponsor worth a vent would place their name on z. aRC car today, because they're the opposite of what today's sportsfans expect, and that's excitement, something that the turf ARC cars just cannot bring. Us mullets need rooosting weapons!!!!

Remember I am talking about a Tassie state round here though. If every round of the Tassie series attracted 25-30 cars it would be in rude health. Obviously for NSW/Vic you would expect more around the 50-60 mark (but I have no idea how many they attract). Look at the Alpine though attracting 100+ entries.

You will get no argument from me about the ARC being rubbish and Group N being boring as batshit, which is unfortunate, but to say that justifies gravel rallying dying is a bit iffy. Hopefully ALL forms of rallying (gravel and tarmac) can find ways to live and prosper for many years!

Rally on!

For sure mate, and I'm not wishing death on ANY form of motorsport, but one only need to look at the fields for tarmac rallies........., oversubscribed entries, fields of 200+ cars, manufacturer support etc..... and this, despite the typical entry fee for tarmac events being outrageously high compared to a typical state gravel round.

  • 3 weeks later...

The ongoing death of forest rallying is a sad but true fact... Although amsag is not doing too bad. Perfect example is Bega rally, 2003 entry was capped at a bit over 100, this year the event did not cover costs due to poor entries. I think the problem is that people with money used to go gravel rallying, but now the people that would have dirt rallied go Tarmac rallying, possibly because they more often than not are promoting their own business and there is simply no way they can justify dirt rallying to any accountant

yes dont get me wrong either

i love gravel rally, it also has the most skilled drivers on the planet in my opinion. i crewed for a gravel team for almost ten years.

i used to love watching possum & neal battle it out in group A weapons and then the wrc cars!! i can still remember how fantastic possums liberty sounded in the forest!!!

rallying is along way from that and i hope they find there way back sometime soon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...