Jump to content
SAU Community

Recommended Posts

i have also heard that (NK) has also ripped his own mother and his exwife and also took the kids from her. And now got married to some spanish girl??

mother is well over 80 years her estate must have been transfered in his name and he won kids in court. Must have done something right with kids that they are staying with him still. Its Australian Court!!!

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

I find it very odd that out of the 36 posts before mine that 21 of them are from new members that have signed up just for this thread, never seen anything like this before........

It was a fairly big group that was owned by KS and NK not just NMG, word gets around as it does.

But judging by whats happening here it does seem like there are individuals trolling the interwebs looking for any reason to give their 2c on this matter. they should make their own forum :cool:

rumours that KS been squeezing money from WSA accounts!! almost 300k in OCT. things happen when partnership fails. KS and nadeems ex wife in abid to buy NMG............?? Is it true???

really????

truth is

since the end of august Kevin Shaw has not set foot on nepean motor group soil until the 19th of december as he was on long service leave while nadeem khan tryed to raise the money to buy him out

esanda said no " i wonder why lol"

wonder will the housing commission in the druitt hook him up after the 29th lol

really????

truth is

since the end of august Kevin Shaw has not set foot on nepean motor group soil until the 19th of december as he was on long service leave while nadeem khan tryed to raise the money to buy him out

esanda said no " i wonder why lol"

wonder will the housing commission in the druitt hook him up after the 29th lol

whats happening after 29th???????????

whats happening after 29th???????????
The Daily Telegraph

At this stage no statement of claim or defence has been filed and the asset-freezing order expires on January 29, when the parties are due to return to court.

Simply amazing! so much interest in one little man, it is the 4th website down when you google Nepean Motor Group! hmmmm seems a few ex & current employees have an axe to grind?

Be interesting to see what happens if & when they get new owners.............

hmm, I wonder whistleblower are u nadeem khan???? Kev may be headed towards the druitt, but looks like according to today's telegraph nadeem will be going elsewhere and it aint the druitt, no loui vuitton there!! Looks like ASIC has some plans for him. Read on my friends. Ps what colour are they wearing these days in the jails??

hmm, I wonder whistleblower are u nadeem khan???? Kev may be headed towards the druitt, but looks like according to today's telegraph nadeem will be going elsewhere and it aint the druitt, no loui vuitton there!! Looks like ASIC has some plans for him. Read on my friends. Ps what colour are they wearing these days in the jails??

matey.........the guy has been king and smart enough to turn things around..........all nmg employees rest assure he will come back!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...