Jump to content
SAU Community

Recommended Posts

2871?

I run a low mount GT3037 pushing 300rwkw and 720nm of torque.

Car is a standard R33 Series 2 with mags. Got suspension but it doesn't even look lowered.

Everything looks pretty much stock.

Is that 300rwkw on stock internals?

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Is that 300rwkw on stock internals?

Sure is, completely stock engine.

Since this dyno graph, I've leaned it to 12.7:1, and fixed that bump in the curve. That was at 18psi, I've also since had it up to 22psi. Makes a fair whack more power at that boost, but I couldn't control the boost properly so I pulled it back to 19psi.

I do ALL of my own tuning.

314rwkw-2.jpg

Edited by The Mafia

In reguards to R31Nismoid's post, HKS make whats called a HKS Silent Exhaust System.

You still get the flow and the nice cannon muffler but the noise is near to nothing. Probley just a slight rumble on full throttle and thats it.

Well I've currently got a custom exhaust with 2 mufflers being made at the moment, it's a backyard job though, so I hope that doesn't hinder me.

So getting a PFC rather than remapping the stock ecu is that much more beneficial? Let's say I get a PFC and get done, when I swap my stock one back in will my car run like goat's cheese? Ie. pass an emissions test, assuming I have a high flow turbo ect.?

If that's the case I might just do that unless I can get away with just the sock ecu remapped.

Nothing wrong with backyard jobs :D MOst of mine is backyard work, and better than any exhause shop in town.

As for emmissions -

I'd talk to Guilt-Toy, he's passed emmissions with a Powerfc and 380rwkw.

He might know the tricks to get emmisions passed with a remap, or even a daughteboard.

Ok well I've been doing some more research and I've been looking at getting a hi-flow r34 turbo, stealth intercooler kit, painted injectors, my custom exhaust.

I'm thinking about heading down to racepace since the are near my house and getting their advice too,

Will need to get a stock airbox with hi-flow filters to replace my pod.

Anything I've missed guys or any other suggestions?

Thanks heaps!

:spank: YEH bottom mount turbos are sweet,also a greddy hideaway intercooler is good,basically replaces the stock one,but is 5 times bigger..cams ,certain n/a tunes help compliment turbos ...cams,lifters.most internals,short shift kit...good rubber get what power u have to the ground...oversize everrtything...throttle bodies...etc... power chip.... tune...etc :devil:

post-58752-1230550739_thumb.png

EPA open the ECU covers if they suspect a chip, so either way...

Jesus christ you guys have it hard down there!! Beginning to understand why more and more of you guys keep everything looking stock on your cars.

Nothing wrong with backyard jobs :devil: MOst of mine is backyard work, and better than any exhause shop in town.

As for emmissions -

I'd talk to Guilt-Toy, he's passed emmissions with a Powerfc and 380rwkw.

He might know the tricks to get emmisions passed with a remap, or even a daughteboard.

This is Vic - there is no way to pass for the average punter. It costs more than all the mods put together so not worth it.

Simple as that.

NSW + Vic = not same. Cannot compare.

Well I've currently got a custom exhaust with 2 mufflers being made at the moment, it's a backyard job though, so I hope that doesn't hinder me.

So getting a PFC rather than remapping the stock ecu is that much more beneficial? Let's say I get a PFC and get done, when I swap my stock one back in will my car run like goat's cheese? Ie. pass an emissions test, assuming I have a high flow turbo ect.?

If that's the case I might just do that unless I can get away with just the sock ecu remapped.

You'll pass easily.

idle and no load emissions will barely change with a larger turbo as the test does not involve loading up the motor.

Its been done time and time again by people, hence i recommended it.

Jesus christ you guys have it hard down there!! Beginning to understand why more and more of you guys keep everything looking stock on your cars.

Ye i must say i was surprised when he opened my ECU cover to check for a chip... lucky i didn't have my "special" stock ECU in there :spank:

Wet shots of gas can very, very easily be hidden. You can set it up so its virtually invisible. Hardest thing is hiding the bottle somewhere that isn't obvious.....

just mount the bottle in the cavity between the boot and back seat, just above the fuel tank access (if its a r33)

I don't think cops look in there?

Wet shots of gas can very, very easily be hidden. You can set it up so its virtually invisible. Hardest thing is hiding the bottle somewhere that isn't obvious.....

Yes they can but, you don't need to and shouldn't. The bottle needs good ventilation around it.

Taking a setup kit out can be a 10-15min job, leaving behind only a secured braided line, bottle bracket and plumbed in fogger with a couple of little screw on caps on it. Too easy :cheers:

It's a great option for someone wanting to go drag racing on the odd occasion. If the power requirement is only 150rwhp or so then you can get something like the Zex solenoid setup that looks to me to be the easiest to plug in and un plug quick for a visit to the strip. Although I believe they only offer smaller kits.

Adriano,

11's with stock intake (not restrictive really) stock Turbo (2rismo has already done it with a fairly small shot) and stock exhaust (well thats the nasty bit) do-able still. Little bigger shot needed perhaps a 125 to 150hp-ish.

Food for thought. :)

just leave your airbox and upgrade the standard side mount, you doing track work? high flow the standard turbo and get bigger injectors and pfc and your laughing. bingo bango job done and car still looks standardish.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...