Jump to content
SAU Community

Recommended Posts

2871?

I run a low mount GT3037 pushing 300rwkw and 720nm of torque.

Car is a standard R33 Series 2 with mags. Got suspension but it doesn't even look lowered.

Everything looks pretty much stock.

Is that 300rwkw on stock internals?

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Is that 300rwkw on stock internals?

Sure is, completely stock engine.

Since this dyno graph, I've leaned it to 12.7:1, and fixed that bump in the curve. That was at 18psi, I've also since had it up to 22psi. Makes a fair whack more power at that boost, but I couldn't control the boost properly so I pulled it back to 19psi.

I do ALL of my own tuning.

314rwkw-2.jpg

Edited by The Mafia

In reguards to R31Nismoid's post, HKS make whats called a HKS Silent Exhaust System.

You still get the flow and the nice cannon muffler but the noise is near to nothing. Probley just a slight rumble on full throttle and thats it.

Well I've currently got a custom exhaust with 2 mufflers being made at the moment, it's a backyard job though, so I hope that doesn't hinder me.

So getting a PFC rather than remapping the stock ecu is that much more beneficial? Let's say I get a PFC and get done, when I swap my stock one back in will my car run like goat's cheese? Ie. pass an emissions test, assuming I have a high flow turbo ect.?

If that's the case I might just do that unless I can get away with just the sock ecu remapped.

Nothing wrong with backyard jobs :D MOst of mine is backyard work, and better than any exhause shop in town.

As for emmissions -

I'd talk to Guilt-Toy, he's passed emmissions with a Powerfc and 380rwkw.

He might know the tricks to get emmisions passed with a remap, or even a daughteboard.

Ok well I've been doing some more research and I've been looking at getting a hi-flow r34 turbo, stealth intercooler kit, painted injectors, my custom exhaust.

I'm thinking about heading down to racepace since the are near my house and getting their advice too,

Will need to get a stock airbox with hi-flow filters to replace my pod.

Anything I've missed guys or any other suggestions?

Thanks heaps!

:spank: YEH bottom mount turbos are sweet,also a greddy hideaway intercooler is good,basically replaces the stock one,but is 5 times bigger..cams ,certain n/a tunes help compliment turbos ...cams,lifters.most internals,short shift kit...good rubber get what power u have to the ground...oversize everrtything...throttle bodies...etc... power chip.... tune...etc :devil:

post-58752-1230550739_thumb.png

EPA open the ECU covers if they suspect a chip, so either way...

Jesus christ you guys have it hard down there!! Beginning to understand why more and more of you guys keep everything looking stock on your cars.

Nothing wrong with backyard jobs :devil: MOst of mine is backyard work, and better than any exhause shop in town.

As for emmissions -

I'd talk to Guilt-Toy, he's passed emmissions with a Powerfc and 380rwkw.

He might know the tricks to get emmisions passed with a remap, or even a daughteboard.

This is Vic - there is no way to pass for the average punter. It costs more than all the mods put together so not worth it.

Simple as that.

NSW + Vic = not same. Cannot compare.

Well I've currently got a custom exhaust with 2 mufflers being made at the moment, it's a backyard job though, so I hope that doesn't hinder me.

So getting a PFC rather than remapping the stock ecu is that much more beneficial? Let's say I get a PFC and get done, when I swap my stock one back in will my car run like goat's cheese? Ie. pass an emissions test, assuming I have a high flow turbo ect.?

If that's the case I might just do that unless I can get away with just the sock ecu remapped.

You'll pass easily.

idle and no load emissions will barely change with a larger turbo as the test does not involve loading up the motor.

Its been done time and time again by people, hence i recommended it.

Jesus christ you guys have it hard down there!! Beginning to understand why more and more of you guys keep everything looking stock on your cars.

Ye i must say i was surprised when he opened my ECU cover to check for a chip... lucky i didn't have my "special" stock ECU in there :spank:

Wet shots of gas can very, very easily be hidden. You can set it up so its virtually invisible. Hardest thing is hiding the bottle somewhere that isn't obvious.....

just mount the bottle in the cavity between the boot and back seat, just above the fuel tank access (if its a r33)

I don't think cops look in there?

Wet shots of gas can very, very easily be hidden. You can set it up so its virtually invisible. Hardest thing is hiding the bottle somewhere that isn't obvious.....

Yes they can but, you don't need to and shouldn't. The bottle needs good ventilation around it.

Taking a setup kit out can be a 10-15min job, leaving behind only a secured braided line, bottle bracket and plumbed in fogger with a couple of little screw on caps on it. Too easy :cheers:

It's a great option for someone wanting to go drag racing on the odd occasion. If the power requirement is only 150rwhp or so then you can get something like the Zex solenoid setup that looks to me to be the easiest to plug in and un plug quick for a visit to the strip. Although I believe they only offer smaller kits.

Adriano,

11's with stock intake (not restrictive really) stock Turbo (2rismo has already done it with a fairly small shot) and stock exhaust (well thats the nasty bit) do-able still. Little bigger shot needed perhaps a 125 to 150hp-ish.

Food for thought. :)

just leave your airbox and upgrade the standard side mount, you doing track work? high flow the standard turbo and get bigger injectors and pfc and your laughing. bingo bango job done and car still looks standardish.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...