Jump to content
SAU Community

Recommended Posts

Up and running again. Ended up having to rebuild my master cylinder as that dumped its seals at the same time... bloody thing is relentless. Bedded new brakes in and all seems good. Thanks again for providing this.

  • Replies 447
  • Created
  • Last Reply

Top Posters In This Topic

nope, sorry. RDA won't do it, unless you're willing to order 1 (forklift) crate consisting of 120 pieces of rotors as a minimum order, they will do it.

maybe you gather 60 owners of those who need blank rotors and share the cost?

Tom, Dav - quotes sent.

Dav0, if your post not enough to send me pm, email me: rsoputro at hotmail dot com

(replace at & dot - you know the drill).

Rianto, would it be safe to sand the midle section of the rotors (not where pads have contact) to get rid off the surface rust and then apply a very thin layer of fish oil to stop it from rusting ?

hm, even a thin layer of oil might splash and leek around - what if it slowly seeps on towards the friction area while the wheel is spinning @ 100km/h?

unless you're preparing for an auto salon or show and shine competition, I wouldn't bother doing it mate...

or if you want you can try finding any hub cover off the internet which is made of coloured anodised aluminium, which could be used to conceal the surface rust on hubs... just be careful that they're not too thick that they reduce the contact amount of your bolt thread.

would you be able to pm me with a quote for slotted rotors front and rear (if you could keep these separate that would be great, cause im not sure if ill replace my rears or just machine them.. all depends on cost) for a R33 GTS T ? Could you also include quotes for the green and red ebc brake pads, again for a R33 GTS T.

Thanks!

Edited by br3ndan

Are the rotors on it came off R32 GTR or are you just using the R32 GTR calipers?

If the rotors are off a R32 GTR, you can measure the front one's diameter across. If it's 297mm (around 30cm) then it's the early models 89-93

If the rotors are 324mm (around 32 1/2 cm) then it's off a 93-94 late V-Spec II model.

Hope that helps...

Hey mate, I am interested in a full set (front and rear) of standard slotted rotors to suit the R33 GTS-t.

Let me know how and when you want payment to be made and I'll make the arrangements.

Thanx champ. :bunny:

roland, quote sent..

Malz34, order added to the list...

RDA group buy 48 order list:

- aleks (payment cleared)

- Malz34 (waiting for payment to clear)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...