Jump to content
SAU Community

Recommended Posts

I was looking at my cat the other day, and i noticed that there is a sensor in the cat,i think its a secondary 02sensor.Anyway its been weld to the cat so if it is a 02 then im guess that it would be stuffed after the heat of being welded.Where can i get new 1 and whats it there 4.

Link to comment
https://www.sau.com.au/forums/topic/25201-wtf-is-the-sensor-in-the-r33-cat/
Share on other sites

The EGT sensor illuminates a warning light which looks like a side view of the catalytic converter with wavey heat lines coming off the top of it (looks more like a BBQ!) It will illuminate when the temperature has reached around 850 degree celcius. This is very hot, and is usually due to either driving the car very hard continuously (ie: around a race track) or if driving normally is due to an extremely lean engine conditions (not good! perhaps a lazy fuel pump?)

This doesn't affect the operations of the ECU, but serves its purpose to help protect both the turbo from excessive heat (ceramic turbines in particular) from high temp failure and also to help the Platinum Rhodium material in the catalytic converter from being heat damaged.

Heat damage reduces the cat's ability to convert carbon monoxide and other poisonous gases back to a safe (and legal) emissions standards. Most cats don't work too well after 80,000km's anyway, from what i've been told.

If you ignore the warning light, then i think you'd be taking a blind eye to a possible engine problem if the light come on when you were just driving around normally (ie: not doing laps on a track)

Hmm, could be a faulty EGT sensor, but i still think that it could be indicating an engine that is running a bit too lean. I hear stories from a dyno operator i know here that sees cars that come in every day that have been so called "tuned" or "dynoed" that run extremely lean in the quest to extract as much power as possible. He says that some performance shops tune the cars so aggressively to extract as much power as possible to impress their customers, when in reality it's better to tune conservatively on a street car taking into consideration different qualities of fuel from batch to batch, different ambient temps, etc, etc. Too many variables to consider, and you should be factoring in some reliability into the engine with some form of thermal control. (A bit richer from Stoichiometric)

Anyway, i'm rambling again, get it looked into! At least check your fuel pressure and A/F ratios, as a EGT warning is a rare instance on a street car, i'm told.

um mods where safc,fmic,9psi,hks filter hi flow muffler. 212hp or round there.They told me my exhaust is causing issue's.I think the fuel pump is stuffed to.Seeings im not driving it im saving heaps of cash and im getting 3inch turbo back exhaust,255lpr pump,malapasi reg,To4e,plenum modified like a gtr style.Cause i think the turbo is a bit tired.Ill see how that runs if it still unpowerd then wolf3d,injectors,manual.I do alot of my mods myself (still building 327hp sohc vtec civic,time for body work:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
    • @dbm7 and @GTSBoy thank you both very much! will give that a shot!
×
×
  • Create New...