Jump to content
SAU Community

Recommended Posts

ok so heres a bit of info

Just picked em up

P1150025.jpg

P1150027.jpg

grabbed some purple as well

P1150026.jpg

brad had to take some meat from the turbine housings to match to the new manifolds

P1150031.jpg

P1150032.jpg

as you can see below a fair bit had to go

P1150033.jpg

installing the new studs

P1150034.jpg

dumps joined

P1150035.jpg

manifolds attached

P1160037.jpg

P1160038.jpg

P1160039.jpg

nice pair

P1160040.jpg

Hmm i can see why there is no point in putting manifolds with small low mounts.. happy sticking with stockers now!

The size difference from that rear housing to the manifold gasket is huge!!!

very nice i have just started to do the same thing with my car atm going the same turbos to :P

any tips for taking them off?

run into any problems fitting them?

i have heard you have to do some mods to the oil return holes?

were did you get your gaskits from?

did you buy a kit?

or just get them from nissan?

can not wait to get mine on there and tuned!!!! :blink:

very nice i have just started to do the same thing with my car atm going the same turbos to :P

any tips for taking them off? - not really just keep your cool lol

run into any problems fitting them? - just doing up the bolts for the manifold when reinstalling

i have heard you have to do some mods to the oil return holes? - yes just drill the bolt holes a bit bigger to match the holes on the turbo thats what i did

were did you get your gaskits from? - kudos motorsports trader on here tell him jason sent you

did you buy a kit? - from kudos motorsports

or just get them from nissan? - lol no

can not wait to get mine on there and tuned!!!! :blink:

Looks the goods mate :laugh: Im very interested to see what numbers you pull! I had a set of these put on my car 2 weeks ago and made 258rwkw on 14 psi and 316rwkw on 18psi on a Mainline dyno, but i used match ported standard manifolds and HKS split dumps and D-Jectro. Good luck and i hope all goes well :)

Yep I got the tomeii stainless manifolds and port matched to the turbine, it's worth doing it on the standard manifolds too as it's a major restriction as stock. You get a much better spool response. Ported like in this pic. Gonna have to do a side by side soon Jase! Here's also the CES race dumps for those interested.....

post-48345-1232448521_thumb.jpg

post-48345-1232448986_thumb.jpg

Edited by doo doo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...